- 您现在的位置：买卖IC网 > PDF目录14532 > MIC2204YMM TR (Micrel Inc)IC REG BUCK SYNC ADJ 0.6A 10MSOP PDF资料下载
参数资料
| 型号： | MIC2204YMM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 0.6A 10MSOP |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 1V |
| 输入电压： | 2.3 V ~ 5.5 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 2MHz |
| 电流 - 输出： | 600mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 剪切带 (CT) |
| 供应商设备封装： | 10-MSOP |
| 产品目录页面： | 1092 (CN2011-ZH PDF) |
| 其它名称： | 576-1071-1 |
MIC2204
Figure 2 shows an efficiency curve. On the non-shaded
portion, from 0 to 200mA, efficiency losses are dominated by
quiescent current losses, gate drive and transition losses. In
this case, lower supply voltages yield greater efficiency in that
they require less current to drive the MOSFETs and have
reduced input power consumption.
Micrel, Inc.
ing output voltage regulation. With a typical gain bandwidth of
200kHz, the MIC2204 is capable of extremely fast transient
responses.
The MIC2204 is designed to be stable with a 4.7 μ H inductor
and a 4.7 μ F ceramic (X5R) output capacitor for output
voltages greater than 1.6V. For output voltages less than
100
95
Efficiency
vs. Output Current
1.6V, a 10 μ F capacitor is required. Also, when a feed forward
capacitor is used, the gain bandwidth is increased to unity
gain. This will also require increasing the output capacitor to
90
85
80
75
70
65
60
4.2V IN
5V IN
3.6V IN
10 μ F.
Feedback
The MIC2204 provides a feedback pin to adjust the output
voltage to the desired level. This pin connects internally to an
error amplifier. The error amplifier then compares the voltage
55
50
0
3.3V OUT
100 200 300 400 500
at the feedback to the internal 1V reference voltage and
adjusts the output voltage to maintain regulation. To calculate
? V OUT
± 1 ?
? V
V OUT OUT
? V OUT OUT + L PD ? ? ?
Efficiency Loss = ? 1± ? ? ? × 100
? ?
OUTPUT CURRENT (A)
Figure 2.
On the shaded region, 200mA to 500mA, efficiency loss is
dominated by MOSFET R DSON and inductor losses. Higher
input supply voltages will increase the Gate-to-Source thresh-
old on the internal MOSFETs, reducing the internal R DSON .
This improves efficiency by reducing DC losses in the device.
All but the inductor losses are inherent to the device, making
inductor selection even more critical in efficiency calcula-
tions. As the inductors are reduced in size, the DC resistance
(DCR) can become quite significant. The DCR losses can be
calculated as follows:
L PD =I OUT2 x DCR
From that, the loss in efficiency due to inductor resistance can
be calculated as follows:
? ? × I ? ?
× I
Efficiency loss due to DCR is minimal at light loads and gains
significance as the load is increased. Inductor selection
becomes a trade-off between efficiency and size in this case.
Compensation
The MIC2204 is an internally compensated, voltage-mode
buck regulator. Voltage mode is achieved by creating an
internal 2MHz ramp signal and using the output of the error
amplifier to pulsewidth modulate the switch node, maintain-
the resistor divider network for the desired output is as
follows:
R1
R2 =
?
? REF ?
Where V REF is 1.0V and V OUT is the desired output voltage.
A 10k ? or lower resistor value from the output to the feedback
is recommended. Larger resistor values require an additional
capacitor (feed-forward) from the output to the feedback. The
large high-side resistor value and the parasitic capacitance
on the feedback pin (~10pF) can cause an additional pole in
the loop. The additional pole can create a phase loss at
high-frequency. This phase loss degrades transient response
by reducing phase margin. Adding feed-forward capacitance
negates the parasitic capacitive effects of the feedback pin.
A minimum 1000pF capacitor is recommended for feed-
forward capacitance.
Also, large feedback resistor values increase the impedance,
making the feedback node more susceptible to noise pick-up.
A feed-forward capacitor would also reduce noise pick-up by
providing a low impedance path to the output.
When using a feed-forward capacitor, the gain bandwidth of
the device reaches unity gain at high-frequency. Therefore,
output capacitance will need to be increased to a minimum
10 μ F. For more information on output capacitor selection for
stability, see the “Compensation ” section.
April 2005
9
M9999-042205
相关PDF资料 |
PDF描述 |
|---|---|
| AP1501A-12K5L-13 | IC REG BUCK 12V 5A TO263-5L |
| HCM24DSAH | CONN EDGECARD 48POS R/A .156 SLD |
| 380LX152M200K052 | CAP ALUM 1500UF 200V 20% SNAP |
| HMM11DRKF | CONN EDGECARD 22POS DIP .156 SLD |
| 380LQ182M160J452 | CAP ALUM 1800UF 160V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2205 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:2MHz PWM Synchronous Buck Regulator with LDO Standby Mode |
| MIC2205_06 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:2MHz PWM Synchronous Buck Regulator with LDO Standby Mode |
| MIC2205-1.38YML | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:2MHz PWM Synchronous Buck Regulator with LDO Standby Mode |
| MIC2205-1.38YML TR | 功能描述:直流/直流开关调节器 2MHz Synchronous Buck Regulator (Lead Free) RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC2205-1.3YML | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:2MHz PWM Synchronous Buck Regulator with LDO Standby Mode |
发布紧急采购，3分钟左右您将得到回复。