参数资料
型号: MIC2211-MFYML TR
厂商: Micrel Inc
文件页数: 9/10页
文件大小: 0K
描述: IC REG LDO 2.8V/1.5V 10-MLF
标准包装: 1
稳压器拓扑结构: 正,固定式
输出电压: 2.8V,1.5V
输入电压: 2.25 V ~ 5.5 V
电压 - 压降(标准): 0.12V @ 150mA,0.24V @ 300mA
稳压器数量: 2
电流 - 输出: 150mA,300mA
电流 - 限制(最小): 150mA,300mA
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 10-VFDFN 裸露焊盘,10-MLF?
供应商设备封装: 10-MLF?(3x3)
包装: 标准包装
产品目录页面: 1095 (CN2011-ZH PDF)
其它名称: 576-2616-6
MIC2211
Functional Description
Adjustable Regulator Design
Micrel, Inc.
The MIC2211 is a high performance, low quiescent current,
power management IC consisting of two μ Cap low dropout
regulators. The ?rst regulator is capable of sourcing 150mA
at output voltages from 1.25V to 5V; the second regulator
is capable of sourcing 300mA of current at output voltages
from 1.25V to 5V.
R1
R2
VOUT1
ADJ1
GND
VOUT2
ADJ2
R1
R2
Enable 1 and 2
V OUT
1.250
Theenableinputsallowforlogiccontrolofbothoutputvolt-
ages with individual enable inputs. The enable input is active
high, requiring 1.8V for guaranteed operation. The enable
input is CMOS logic and cannot by left ?oating.
Input Capacitor
Good bypassing is recommended from input to ground to
help improve AC performance. A 1 μ F capacitor or greater
located close to the IC is recommended.
Bypass Capacitor
The internal reference voltage of the MIC2211 can be bypassed
with a capacitor to ground to reduce output noise and increase
power supply rejection (PSRR). A quick-start feature allows
for quick turn-on of the output voltage regardless of the size
of the capacitor. The recommended nominal bypass capacitor
is 0.01 μ F, but it can be increased without limit.
Output Capacitor
Each regulator output requires a 1 μ F ceramic output capaci-
tor for stability. The output capacitor value can be increased
to improve transient response, but performance has been
optimized for a 1 μ F ceramic type output capacitor.
X7R/X5R dielectric-type ceramic capacitors are recom-
mended because of their temperature performance. X7R-type
capacitors change capacitance by 15% over their operating
temperature range and are the most stable type of ceramic
capacitors. Z5U and Y5V dielectric capacitors change value
by as much as 50% and 60% respectively over their operat-
ing temperature ranges. To use a ceramic chip capacitor with
Y5V dielectric, the value must be much higher than an X7R
ceramic capacitor to ensure the same minimum capacitance
over the equivalent operating temperature range.
MIC2211 Adjustable Regulator Design
The MIC2211 allows the programming of the output voltages
1 and 2 anywhere between 1.25V and 5.5V, the maximum
operating rating of the part. Two resistors are required for each
output. Appropriate resistor values are required to prevent
the low quiescent current performance being compromised.
Resistor values recommended are between 100k? and
500k?.
The resistor values are calculated by:
R1 = R2 – 1
where V OUT is the desired output voltage. Calculate sepa-
rately for each output.
October 2005
9
M9999-101805
相关PDF资料
PDF描述
MIC2211-FMYML TR IC REG LDO 1.5V/2.8V 10-MLF
ESC36DRTS-S13 CONN EDGECARD 72POS .100 EXTEND
RCB22DHAR CONN EDGECARD 44POS R/A .050 DIP
GSC19DTEN CONN EDGECARD 38POS .100 EYELET
EMM40DTKI-S288 CONN EDGECARD 80POS .156 EXTEND
相关代理商/技术参数
参数描述
MIC2211-MGBML 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Dual UCap LDO in 3mm 】 3mm MLF⑩
MIC2211-MGBML TR 功能描述:IC REG LDO 2.8V/1.8V 10-MLF RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正,固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降(标准):0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制(最小):- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A,SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND
MIC2211-MGYML 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述:
MIC2211-MGYML TR 功能描述:低压差稳压器 - LDO Dual Cap LDO in 3mm x 3mm MLF (Lead Free) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压(最大值):307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
MIC2211-MGYML-TR 功能描述:Linear Voltage Regulator IC Positive Fixed 2 Output 2.8V, 1.8V 150mA, 300mA 10-MLF? (3x3) 制造商:microchip technology 系列:- 包装:剪切带(CT) 零件状态:停产 稳压器拓扑:正,固定式 电压 - 输出:2.8V,1.8V 电流 - 输出:150mA,300mA 电压 - 跌落(典型值):0.12V @ 150mA,0.24V @ 300mA 稳压器数:2 电压 - 输入:2.25 V ~ 5.5 V 电流 - 限制(最小值):150mA,300mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-VFDFN 裸露焊盘,10-MLF? 供应商器件封装:10-MLF?(3x3) 标准包装:1