参数资料
| 型号： | MIC2215-PPMYML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3V/3V/2.8V .25A 16MLF |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3V，3V，2.8V |
| 输入电压： | 2.25 V ~ 5.5 V |
| 电压 - 压降（标准）： | 0.17V @ 250mA |
| 稳压器数量： | 3 |
| 电流 - 输出： | 250mA |
| 电流 - 限制（最小）： | 350mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN Exposed Pad，16-MLF? |
| 供应商设备封装： | 16-MLF?（4x4） |
| 包装： | 剪切带 (CT) |
| 产品目录页面： | 1095 (CN2011-ZH PDF) |
| 其它名称： | 576-1073-1 |
Micrel, Inc.
Application Information
Enable/Shutdown
The MIC2215 comes with three active-high enable pins
that allow control of each individual regulator to be either
disabled or enabled. Forcing the enable pin low disables
the respective regulator and sends it into a “zero” off-
mode-current state. In this state, current consumed by
the individual regulator goes nearly to zero. This is true
for both regulators 2 and 3. Regulator 1’s input supply
pin is also used to power the internal reference. When
any regulator; either 1, 2, or 3 is enabled, an additional
20μA for the reference will be drawn through V IN1 . All
three must be disabled to enter the “zero” current-off-
mode-state. Forcing the enable pin high enables each
respective output voltage. This part is CMOS and none
of the enable pins can be left floating; a floating enable
pin may cause an indeterminate state on the output.
Input Capacitor
The MIC2215 is a high performance, high bandwidth
device. Therefore, it requires a well-bypassed input
supply for optimal performance. A small 0.1μF capacitor
placed close to the input is recommended to aid in noise
performance. Low-ESR ceramic capacitors provide opti-
mal performance at a mini-mum of space. Additional
high-frequency capacitors such as small valued NPO
dielectric type capacitors help to filter out high frequency
noise and are good practice in any RF-based circuit.
Output Capacitor
The MIC2215 requires an output capacitor for stability.
The design requires 1μF or greater on the output to
maintain stability. The design is optimized for use with
MIC2215
Internal Reference
The internal band gap, or reference, is powered from the
V IN1 input. Due to some of the input noise (PSRR)
contributions being imposed on the band gap, it is
important to make V IN1 as clean as possible with good
bypassing close to the input.
Multiple Input Supplies
The MIC2215 can be used with multiple input supplies
when desired. The only requirement, aside from
maintaining the voltages within the operating ranges, is
that V IN1 always remains the highest voltage potential.
No-Load Stability
The MIC2215 will remain stable and in regulation with no
load, unlike many other voltage regulators. This is
especially important in CMOS RAM keep-alive app-
lications.
Thermal Considerations
The MIC2215 is designed to provide up to 250mA of
current per channel in a very small package. Maximum
power dissipation can be calculated based on the output
current and the voltage drop across the part. To
determine the maximum power dissipation of the
package, use the junction-to-ambient thermal resistance
of the device and the following basic equation:
P D(max) = (T J(max) – T A )÷ θ JA
T J(max) is the maximum junction temperature of the die,
125°C, and T A is the ambient operating temperature. θ JA
is layout dependent; Table 2 shows examples of the
junction-to-ambient thermal resistance for the MIC2215.
low-ESR ceramic chip capacitors. X7R/X5R dielectric-
type ceramic capacitors are recommended because of
their temperature performance. X7R-type capacitors
change capacitance by 15% over their operating temp-
Package
16-Pin 4mm x 4mm MLF ?
θ JA Recommended
Minimum Footprint
43°C/W
Table 2. MLF Thermal Resistance
erature range and are the most stable type of ceramic
capacitors. Z5U and Y5V dielectric capacitors change
value by as much as 50% and 60%, respectively, over
their operating temperature ranges. To use a ceramic
chip capacitor with Y5V dielectric, the value must be
much higher than an X7R ceramic capacitor to ensure
the same minimum capacitance over the equivalent
operating temperature range.
Bypass Pin
A capacitor can be placed from the noise bypass pin to
ground to reduce output voltage noise. The capacitor
bypasses the internal reference. There is one single
internal reference shared by each output, therefore the
bypassing affects each regulator. A 0.1μF capacitor is
recommended for applications that require low-noise
outputs. The bypass capacitor can be increased, further
reducing noise and improving PSRR. Turn-on time
increases slightly with respect to bypass capacitance.
?
The actual power dissipation of the regulator circuit can
be determined using the equation:
P DTOTAL = P DLDO1 + P DLDO2 + P DLDO3
P DLDO1 = (V IN1 – V OUT1 ) × I OUT1
P DLDO2 = (V IN2 – V OUT2 ) × I OUT2
P DLDO3 = (V IN3 – V OUT3 ) × I OUT3
Substituting P D (max) for P D and solving for the operating
conditions that are critical to the application will give the
maximum operating conditions for the regulator circuit.
For example, when operating the MIC2215 at 60°C with
a minimum footprint layout, the maximum load currents
can be calculated as follows:
P D (max) = (125°C – 60°C)/43 °C/W
P D (max) = 1.511W
January 2007
9
M9999-011207
相关PDF资料 |
PDF描述 |
|---|---|
| RBB92DHAN-S250 | EDGECARD PCI 184POS .050 R/A 5V |
| RBB92DHAD-S250 | EDGECARD PCI 184POS .050 R/A 5V |
| LFXP3E-3Q208C | IC FPGA 3.1KLUTS 136I/O 208-PQFP |
| RSC44DRAS | CONN EDGECARD 88POS R/A .100 SLD |
| LFXP3C-3Q208C | IC FPGA 3.1KLUTS 136I/O 208-PQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2215-PPPBML | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Tirple High PSRR, Low Noise uCap LDO |
| MIC2215-PPPBML TR | 功能描述:IC REG LDO 3V .25A 16MLF RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC2215-PPPBML-EV | 功能描述:MIC2215 3 - Triple Channels per IC Positive Fixed Linear Voltage Regulator Evaluation Board 制造商:microchip technology 系列:- 零件状态:无货 每 IC 通道数:3 - 三 电压 - 输出:3V，3V，3V 电流 - 输出:250mA，250mA，250mA 电压 - 输入:2.25 V ~ 5.5 V 稳压器类型:正，固定式 工作温度:-40°C ~ 125°C 板类型:完全填充 所含物品:板 使用的 IC/零件:MIC2215 标准包装:1 |
| MIC2215-PPPYML | 功能描述:IC REG LDO 3V .25A 16-MLF RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC2215-PPPYML TR | 功能描述:低压差稳压器 - LDO Triple uCap LDO with High PSRR(Lead Free) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。