- 您现在的位置：买卖IC网 > PDF目录16905 > MIC2537-1BM TR (Micrel Inc)IC USB SWITCH QUAD 16-SOIC PDF资料下载
参数资料
| 型号： | MIC2537-1BM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC USB SWITCH QUAD 16-SOIC |
| 标准包装： | 2,500 |
| 类型： | USB 开关 |
| 输出数： | 4 |
| Rds（开）： | 700 毫欧 |
| 内部开关： | 是 |
| 电流限制： | 250mA |
| 输入电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2537-1BMTR MIC2537-1BMTR-ND |
MIC2537
Applications Information
Supply Filtering
A 0.1 μ F to 1 μ F bypass capacitor from IN to GND, located at
the device, is strongly recommended to control supply tran-
sients. Without a bypass capacitor, an output short may
cause sufficient ringing on the input (from supply lead induc-
tance) to damage internal control circuitry.
Input or output transients must not exceed the absolute
maximum supply voltage (V IN(max) = 6V) even for a short
duration.
V IN
Micrel
In USB applications it is required that output bulk capacitance
shown in “ Typical Application ” is utilized to meet transient
regulation requirements during hot-plug events. When the
MIC2537 is enabled, the flag will go active for about 5ms
depending on output capacitance. Additionally, during hot-
plug events, inrush currents may cause the flag to go active
for approximately 30 μ s. If these “ false ” overcurrent indica-
tions are a system problem, they can be masked by an RC
filter on the flag output (see Figure 2). Alternatively, a 15ms
debounce routine may be programmed into the USB logic
controller to eliminate the need for an RC filter.
Bus-Powered Hub Port Switching
3V to 5.5V
MIC2537
The USB Specification requires that bus-powered hubs imple-
0.1μF to 1μF
FLGA
ENA
FLGB
ENB
ment port switching on either a ganged or individual basis.
The specific implementation must be reported via the Hub
OUTA OUTB
Descriptor Status Register. Individual port switching has
GND
NC
IN
NC
advantages in that a fault on one port will not prevent the other
ports from operating correctly. In addition, a soft-start circuit
must be included in order to reduce inrush currents when the
OUTC OUTD
switch is enabled. To meet this requirement, the MIC2537
ENC
FLGC
END
FLGD
has been designed to slowly ramp its output.
Suspend Current
For hubs, Universal Serial Bus Specification Revision 1.1
Enable Input
Figure 1. Supply Bypassing
section 7.2.3, stipulates that the maximum suspend current
for a configured hub is 2.5mA. This number is derived by
allocating 500 μ A for up to four downstream ports plus 500 μ A
EN must be driven logic high or logic low for a clearly defined
input. Floating the input may cause unpredictable operation.
EN should not be allowed to go negative with respect to GND.
Soft Start
The MIC2537 presents a high impedance when off and slowly
becomes a low impedance as it turns on. This reduces inrush
current and related voltage drop that results from charging a
capacitive load, satisfying the USB voltage droop require-
ments.
Transient Overcurrent Fault-Flag Filter
When the MIC2537 is enabled, large values of capacitance
at the output of the device will cause inrush currents to flow
that exceed the short circuit current-limit threshold of the
device and cause the flag to activate. The duration of this time
depends on the size of the output capacitance. See “ Func-
tional Characteristics: Switch Turn-On and Turnoff
Charcteristics ” for details. During the charging time, the
device enters into constant-current mode and the flag is
activated. As the capacitance is charged the current de-
creases below the short circuit current-limit threshold and the
flag will be deasserted.
for the hub ’ s internal functions. A nonconfigured hub is
considered a low-power device and cannot consume more
than 500 μ A. In a nonconfigured state all downstream devices
will be switched off. In most cases, a nonconfigured hub is not
a practical state for the system. Therefore, the 2.5mA speci-
fication is the applicable target specification for the suspend
state. In a bus-powered hub with less than 4 ports, the hub
may use the additional current for internal functions.
The 500 μ A worst case suspend current must be further
divided among the data port termination resistors and internal
functions. The termination resistors will consume
3.6V ÷ (16.5K ? – 5%) = 230 μ A. This leaves only 270 μ A for
internal functions. Assuming 100 μ A as the maximum USB
controller suspend current, 170 μ A remains for the rest of the
system. The MIC2537 will consume 100 μ A maximum, leav-
ing a margin of 70 μ A.
USB Controller
OVERCURRENT
10k
50k
0.3μF
FLGA
FLGB
FLGC
FLGD
Figure 2. Transient Filter
December 1999
9
MIC2537
相关PDF资料 |
PDF描述 |
|---|---|
| LM4040DEX3-2.5+T | IC VREF SHUNT PREC 2.5V SC-70-3 |
| DC9S08QB8 | DAUGHTER CARD FOR DEMO9S08QB8 |
| LM4040DEX3-3.3+T | IC VREF SHUNT PREC 3.3V SC-70-3 |
| LM4040DEX3-2.1+T | IC VREF SHUNT PREC 2.048V SC70-3 |
| VE-J12-EY | CONVERTER MOD DC/DC 15V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2537-1YM | 功能描述:电源开关 IC - USB Quad USB Switch (Lead Free) RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| MIC2537-1YM TR | 功能描述:电源开关 IC - USB Quad USB Switch (Lead Free) RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| MIC2537-2BM | 功能描述:IC USB SWITCH QUAD 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电源分配开关 系列:- 特色产品:XRP252 Switches 标准包装:1 系列:- 类型:高端开关 输出数:2 Rds（开）:140 毫欧 内部开关:是 电流限制:1.15A 输入电压:1.75 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN（3x3） 包装:Digi-Reel® 其它名称:1016-1691-6 |
| MIC2537-2BM TR | 功能描述:IC USB SWITCH QUAD 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电源分配开关 系列:- 特色产品:XRP252 Switches 标准包装:1 系列:- 类型:高端开关 输出数:2 Rds（开）:140 毫欧 内部开关:是 电流限制:1.15A 输入电压:1.75 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN（3x3） 包装:Digi-Reel® 其它名称:1016-1691-6 |
| MIC2537-2YM | 功能描述:电源开关 IC - USB Quad USB Switch (Lead Free) RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。