- 您现在的位置：买卖IC网 > PDF目录20110 > MIC2584-JYTS (Micrel Inc)IC CTRLR HOT SWAP DUAL 16-TSSOP PDF资料下载
参数资料
| 型号： | MIC2584-JYTS |
| 厂商： | Micrel Inc |
| 文件页数： | 23/28页 |
| 文件大小： | 273K |
| 描述： | IC CTRLR HOT SWAP DUAL 16-TSSOP |
| 标准包装： | 94 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 1 V ~ 13.2 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 1085 (CN2011-ZH PDF) |
| 其它名称： | 576-2195 MIC2584-JYTS-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页
March 2005
23
MIC2584/2585
MIC2584/2585
Micrel
the opposite direction. Here, the worst-case maximum cur-
rent is found using a 57.5mV trip voltage and a sense resistor
that is 3% low in value. The resulting equation is:
I
57.5mV
0.97 R
59.3mV
R
LOAD(CONT,MAX)
SENSE(NOM)
SENSE(NOM)
=
( )
(
)
=
(12)
As an example, if an output must carry a continuous 6A
without nuisance trips occurring, Equation 11
yields:
R
41.3mV
6A
m
SENSE(MAX)
=
=
&
6 88
.
. The next lowest
standard value is 6m&
.
At the other set of tolerance extremes
for the output in question,
I
59.3mV
6.0m
A
LOAD(CONT,MAX)
=
&
= 9 88
.
. Knowing this final da-
tum, we can determine the necessary wattage of the sense
resistor using P = I
2
R, where
I will be I
LOAD(CONT, MAX)
, and
R will be (0.97)(R
SENSE(NOM)
).
These numbers yield the
following: P
MAX
= (9.88A)
2
(5.82m&)
= 0.568W. In this ex-
ample, a 1W sense resistor is sufficient.
MOSFET Selection
Selecting the proper external MOSFET for use with the
MIC2584/85 involves three straightforward tasks:
" Choice of a MOSFET which meets minimum
voltage requirements.
" Selection of a device to handle the maximum
continuous current (steady-state thermal is-
sues).
" Verify the selected parts ability to withstand any
peak currents (transient thermal issues).
MOSFET Voltage Requirements
The first voltage requirement for the MOSFET is easily stated:
the drain-source breakdown voltage of the MOSFET must be
greater than V
IN(MAX)
. For instance, a 12V input may reason-
ably be expected to see high-frequency transients as high as
18V. Therefore, the drain-source breakdown voltage of the
MOSFET must be at least 19V. For ample safety margin and
standard availability, the closest minimum value will be 20V.
The second breakdown voltage criterion that must be met is a
bit subtler than simple drain-source breakdown voltage, but is
not hard to meet. In MIC2584/85 applications, the gate of the
external MOSFET is driven up to approximately 20V by the
internal output MOSFET (again, assuming 12V operation). At
the same time, if the output of the external MOSFET (its source)
is suddenly subjected to a short, the gate-source voltage will go
to (20V 0V) = 20V. This means that the external MOSFET
must be chosen to have a gate-source breakdown voltage of
20V or more, which is an available standard maximum value.
However, if operation is above 12V, the 20V gate-source
maximum will likely be exceeded. As a result, an external Zener
diode clamp should be used to prevent breakdown of the
external MOSFET when operating at voltages above 10V. A
Zener diode with 10V rating is recommended as shown in
Figure 12. At the present time, most power MOSFETs with a
20V gate-source voltage rating have a 30V drain-source break-
down rating or higher. As a general tip, choose surface-mount
devices with a drain-source rating of 30V as a starting point.
Finally, the external gate drive of the MIC2584/85 requires a
low-voltage logic level MOSFET when operating at voltages
lower than 3V. There are 2.5V logic level MOSFETs available.
See Table 5, "MOSFET and Sense Resistor Vendors" for
suggested manufacturers.
I
2
TX_/RX
I
1
V
DD
V
DD
CORE SUPPLY
(V
CC
)
OUTPUT
DRIVER
CIRCUIT
BLOCK
OUTPUT
DRIVER
CIRCUIT
BLOCK
Data In
OE
Data Out
External
Bus Control
I/O
Dual Supply DSP
Peripheral
CORE
I/O SUPPLY
(V
DD
)
Data In
OE
Data Out
Figure 11. Bidirectional Port Bus Contention
相关PDF资料 |
PDF描述 |
|---|---|
| RYM06DRMN-S288 | CONN EDGECARD 12POS .156 EXTEND |
| GRM188R71C333KA01D | CAP CER 0.033UF 16V 10% X7R 0603 |
| T86C225M025EAAS | CAP TANT 2.2UF 25V 20% 2312 |
| 10090096-P154VLF | DSUB STR 15POS PIN |
| 10090098-S154VLF | DSUB STR 15POS SOCKET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2584-JYTS TR | 功能描述:热插拔功率分布 Dual Channel Hot-Swap Controller - 100mV Threshold - Lead Free RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MIC2584-JYTS-TR | 功能描述:Hot Swap Controller 2 Channel General Purpose 16-TSSOP 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 类型:热交换控制器 通道数:2 内部开关:无 应用:通用 特性:闭锁故障 可编程特性:故障超时，压摆率，UVLO 电压 - 电源:1 V ~ 13.2 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:1.7mA 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商器件封装:16-TSSOP 功能引脚:CFILTER，CPOR，/FAULT，FB1，FB2，ON，/POR 标准包装:1 |
| MIC2584-KBTS | 功能描述:IC CTRLR HOT SWAP DUAL 16-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| MIC2584-KBTS TR | 功能描述:IC CTRLR HOT SWAP DUAL 16-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| MIC2585-1JBTS | 功能描述:IC CTRLR HOT SWAP DUAL 24-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。