- 您现在的位置：买卖IC网 > PDF目录22125 > MIC2585-2JYTS (Micrel Inc)IC CTRLR HOT SWAP DUAL 24-TSSOP PDF资料下载
参数资料
| 型号： | MIC2585-2JYTS |
| 厂商： | Micrel Inc |
| 文件页数： | 4/28页 |
| 文件大小： | 273K |
| 描述： | IC CTRLR HOT SWAP DUAL 24-TSSOP |
| 标准包装： | 62 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 1 V ~ 13.2 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 管件 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
MIC2584/2585
Micrel
MIC2584/2585
4
March 2005
Pin Number
Pin Number
Pin Name
Pin Function
MIC2584
MIC2585
3, 14
3, 22
GATE2, GATE1
Gate Drive (Outputs): Connect each output to the gates of external
N-Channel MOSFETs. When ON is asserted, a 14礎 current source is
activated and begins to charge the gate of the N-Channel MOSFET connected
to this pin. An internal clamp ensures that no more than 10V is applied
between the GATE and Source when VCC1 or VCC2 is above 5V. When the
circuit breaker trips or when an input undervoltage lockout condition is
detected, the GATE1 and GATE2 pins are immediately brought low.
9
13
GND
Ground: Tie to analog ground.
7
10
CPOR
Power-On Reset Timer (Input): A capacitor connected between this pin and
ground sets the start-up delay (t
START
) and the power-on reset interval
(t
POR
). Once the lagging supply rises above its UVLO threshold and ON
asserts, the capacitor connected to CPOR begins to charge. When the
voltage at CPOR crosses 0.3V, the start-up threshold (V
START
), a start cycle
is initiated as the GATE outputs begin to ramp while capacitor C
POR
is
immediately discharged to ground. When the voltage at the lagging FB pin
rises above its threshold (V
FB
), capacitor CPOR begins to charge again.
When the voltage at CPOR rises above the power-on reset delay threshold
(V
POR
) of 1.235V, the timer resets by pulling CPOR to ground and /POR is
deasserted. If C
POR
= 0, then t
START
defaults to 20祍.
8
11
CFILTER
Current Limit Response Timer (Input): A capacitor connected to this pin
defines the period of time, t
OCSLOW
, in which an overcurrent event must last
to signal a fault condition and trip the circuit breaker. When an overcurrent
condition occurs, a 2.5礎 current source begins to charge this capacitor. If
the voltage at this pin reaches 1.235V, the circuit breaker is tripped, both
GATE pins immediately shut off, and /FAULT is asserted. If C
FILTER
= 0,
then t
OCSLOW
defaults to 20祍.
5, 12
7, 18
FB2, FB1
Power-Good Threshold Input (Undervoltage Detect): FB1 and FB2 are
internally compared to 1.235V and 0.80V references with 25mV of hyster-
esis, respectively. External resistive divider networks may be used to set the
voltage at these pins. If either FB input momentarily goes below its thresh-
old, then /POR is activated for one timing cycle, t
POR
, indicating an output
undervoltage condition. The /POR signal deasserts one timing cycle after the
FB pin exceeds its power-good threshold by 25mV. A 5祍 filter on these pins
prevents glitches from inadvertently activating the /POR signal.
10
14
/FAULT
Circuit Breaker Fault Status (Output): Active-Low, weak pull-up to VCC1 or
open-drain. Asserted when the circuit breaker is tripped due to an
overcurrent, undervoltage lockout, or overvoltage event. When deasserted,
the MIC2585 will initiate a new start cycle by toggling the ON pin.
11
15
/POR
Power-On Reset (Output): Active Low, weak pull-up to VCC1 or open drain.
This pin remains asserted during start-up until a time period (t
POR
) after the
lagging FB pin threshold (V
FB1
or V
FB2
) is exceeded. The timing capacitor
C
POR
determines t
POR
. When the output voltage monitored at either FB pin
falls below V
FB
, /POR is asserted for a minimum of one timing cycle (t
POR
).
4, 13
5, 20
OUT2, OUT1
Output Voltage Monitor (Inputs): For output tracking, connect these pins to
their respective output to sense the output voltage.
N/A
12
CDLY
Output Sequence Delay Timer (Input): This pin is internally clamped to 6V.
A capacitor connected to this pin sets a timer delay, t
DLY
, between V
OUT1
and V
OUT2
as shown in Figure 5. With this pin pulled up to VCC1 through a
resistor, and if C
GATE1
= C
GATE2
, both V
OUT1
and V
OUT2
ramp up and down
with the same dv/dt as depicted in the Tracking Mode diagram while
maintaining a maximum voltage differential between V
OUT1
and V
OUT2
.
N/A
9
TRK
Discharge Tracking Mode Pin (Input): Tie this pin to OUT1 or OUT2 to
enable tracking during turn-off cycle. Ground this pin to disable tracking
during turn-off. The TRK pin is not to be used as a digital input.
相关PDF资料 |
PDF描述 |
|---|---|
| GRM219R61E225KA12D | CAP CER 2.2UF 25V 10% X5R 0805 |
| M4A5-32/32-10JNC | IC CPLD 32MACRO 44PLCC |
| HSM36DRKN-S13 | CONN EDGECARD 72POS .156 EXTEND |
| HMM36DRKN-S13 | CONN EDGECARD 72POS .156 EXTEND |
| TAP104M035SRS | CAP TANT 0.1UF 35V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2585-2JYTS TR | 功能描述:热插拔功率分布 Dual Channel Hot-Swap Controller - 100mV Threshold - Lead Free RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MIC2585-2JYTSTR | 制造商:RF Micro Devices Inc 功能描述: |
| MIC2585-2JYTS-TR | 功能描述:Hot Swap Controller, Sequencer 2 Channel General Purpose 24-TSSOP 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:过期 类型:热交换控制器，序列发生器 通道数:2 内部开关:无 应用:通用 特性:闭锁故障 可编程特性:故障超时，OVP，压摆率，UVLO 电压 - 电源:1 V ~ 13.2 V 电流 - 输出（最大值）:- 工作温度:-40°C ~ 85°C 电流 - 电源:1.7mA 安装类型:表面贴装 封装/外壳:24-TSSOP（0.173"，4.40mm 宽） 供应商器件封装:24-TSSOP 功能引脚:CDLY，CFILTER，CPOR，DIS1，DIS2，/FAULT，FB1，FB2，ON，OV1，OV2，PG1，PG2，/POR，TRK 标准包装:1 |
| MIC2585-2KBTS | 功能描述:IC CTRLR HOT SWAP DUAL 24-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| MIC2585-2KBTS TR | 功能描述:IC CTRLR HOT SWAP DUAL 24-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。