- 您现在的位置：买卖IC网 > Datasheet目录45 > MIC2587R-2BM TR (Micrel Inc)IC CTRLR HOT SWAP POS HV 8-SOIC Datasheet资料下载
参数资料
| 型号： | MIC2587R-2BM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 4/22页 |
| 文件大小： | 972K |
| 描述： | IC CTRLR HOT SWAP POS HV 8-SOIC |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 10 V ~ 80 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2587R-2BMTR MIC2587R-2BMTR-ND |
icrel, Inc.
MIC2587/MIC2587R
anuary 24, 2013
4
Revision 2.0
Pin Description (Continued)
Pin Number
Pin Name
Pin Function
3
PWRGD
(MIC2587-1)
(MIC2587R-1)
Active-HIGH
/PWRGD
(MIC2587-2)
(MIC2587R-2)
Active-LOW
Power-is-Good (PWRGD or /PWRGD), Open-Drain Output: This pin remains de-asserted during
start up while the FB pin voltage is below the V
FBH
threshold. Once the voltage at the FB pin
rises above the V
FBH
threshold, the Power-is-Good output asserts with minimal delay
(typically d 5祍).
For the (1) options, the PWRGD output pin will be high-impedance when the FB pin voltage is
higher than V
FBH
and will pull down to GND when the FB pin voltage is less than V
FBL
.
For the (2) options, the /PWRGD output pin will be high-impedance when the FB pin voltage is
lower than V
FBL
and will pull down to GND when the FB pin voltage is higher than V
FBH
.
The Power-is-Good output pin is connected to an open-drain, N-channel transistor implemented
with high-voltage structures. These transistors are capable of operating with pull-up resistors to
supply voltages as high as 100V.
To use this signal as a logic control in low-voltage DC/DC conversion applications, an external
pull-up resistor between this pin and the logic supply voltage is recommended unless the DC/DC
module or other load is equipped with a internal pull-up impedance.
4
GND
Tie this pin directly to the systems analog GND plane.
5
TIMER
Current-Limit Response Timer: A capacitor connected from this pin to GND sets the time (t
FLT
)
for which the controller is allowed to remain in current limit before tripping the circuit breaker.
The overcurrent filter is designed to prevent nuisance tripping of the circuit breaker that can be
caused by transient current spikes or other undesired noise . Once the MIC2587 circuit breaker
trips, the output latches off. Under normal (steady-state) operation, the TIMER pin is held to
GND by an internal 3.5礎 current source (I
TIMERDN
). When the voltage across the external sense
resistor exceeds the V
TRIP
threshold, an internal 65礎 current source (I
TIMERUP
) is activated to
charge the capacitor connected to the TIMER pin. When the TIMER pin voltage reaches the
V
TIMERH
threshold, the circuit breaker is tripped pulling the GATE pin low, the I
TIMERUP
current
source is disabled, and the TIMER pin capacitor is discharged by the I
TIMERDN
current source.
When the voltage at the TIMER pin is less than 0.5V, the MIC2587 can be restarted by toggling
the ON pin LOW then HIGH.
For the MIC2587R, the GATE output attempts another start cycle to re-establish the output
voltage when the circuit breaker is tripped upon an overcurrent fault. The capacitor connected to
the TIMER pin sets the period of auto-retry with a fixed, nominal duty cycle of 5%.
6
GATE
Gate Drive Output: This pin is the output of an internal charge pump connected to the gate of an
external, N-channel power MOSFET. The charge pump has been designed to provide a
minimum gate drive (V
GATE
= V
GATE
V
CC
) of +7.5V over the input supplys full operating range.
When the ON pin voltage is higher than the V
ONH
threshold, a 16礎 current source (I
GATEON
)
charges the GATE pin.
When in current limit, the output voltage at the GATE pin is adjusted so that the voltage across
the external sense resistor is held equal to V
TRIP
while the capacitor connected to the TIMER pin
charges. If the current limit condition goes away before the TIMER pin voltage rises above the
V
TIMERH
threshold, then steady-state operation resumes.
The GATE output pin is shut down whenever: (1) the input supply voltage is lower than the V
UVL
threshold, (2) the ON pin voltage is lower than the V
ONL
threshold, (3) the TIMER pin voltage is
higher than the V
TIMERH
threshold, or (4) the difference between the VCC and SENSE pins is
greater than V
TRIP
while the TIMER pin is grounded. For cases (3) and (4) overcurrent fault
conditions the GATE is immediately pulled to ground by I
GATEFLT
, an 80mA pull-down current
source.
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2590B-5BTQ TR | IC PCI HOT PLUG CTLR DUAL 48TQFP |
| MIC2591B-2BTQ TR | IC PCI HOT PLUG CTLR DUAL 48TQFP |
| MIC2592B-2BTQ TR | IC PCI HOT PLUG CTLR DUAL 48TQFP |
| MIC2593-2BTQ TR | IC PCI HOT PLUG CTLR DUAL 48TQFP |
| MIC2594-2BM TR | IC CTRLR HOT SWAP NEG HV 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2587R-2YM | 功能描述:热插拔功率分布 Positive High Voltage Hot-Swap Controller - Lead Free RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MIC2587R-2YM TR | 功能描述:热插拔功率分布 Positive High Voltage Hot-Swap Controller - Lead Free RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MIC2588-1BM | 功能描述:IC CTRLR HOT SWAP NEG HV 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| MIC2588-1BM TR | 功能描述:IC CTRLR HOT SWAP NEG HV 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| MIC2588-1YM | 功能描述:热插拔功率分布 Negative Voltage Hot-swap Controller - Lead Free RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。