- 您现在的位置：买卖IC网 > PDF目录14545 > MIC2601YML TR (Micrel Inc)IC REG BOOST ADJ 1.2A 8MLF PDF资料下载
参数资料
| 型号： | MIC2601YML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 8/13页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST ADJ 1.2A 8MLF |
| 特色产品： | 40V Wide Input Range Boost Regulator |
| 标准包装： | 1 |
| 类型： | 升压（升压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 40V |
| 输入电压： | 4.5 V ~ 20 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1.12MHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-VFDFN 裸露焊盘，8-MLF? |
| 包装： | 标准包装 |
| 供应商设备封装： | 8-MLF?（2x2） |
| 产品目录页面： | 1093 (CN2011-ZH PDF) |
| 其它名称： | 576-3283-6 |
Micrel, Inc.
Functional Description
The MIC2601/2 is a constant frequency, PWM current
mode boost regulator. The block diagram is shown in
Figure 1. The MIC2601/2 is composed of an oscillator,
slope compensation ramp generator, current amplifier,
g m error amplifier, PWM generator, and a 1.2A bipolar
output transistor. The oscillator generates a
1.2MHz/2MHz clock. The clock’s two functions are to
trigger the PWM generator that turns on the output
transistor and to reset the slope compensation ramp
generator. The current amplifier is used to measure the
switch current by amplifying the voltage signal from the
internal sense resistor. The output of the current
amplifier is summed
with the output of the slope compensation ramp
generator. This summed current-loop signal is fed to one
of the inputs of the PWM generator.
The g m error amplifier measures the feedback voltage
through the external feedback resistors and amplifies the
error between the detected signal and the 1.25V
reference voltage. The output of the gm error amplifier
provides the voltage-loop signal that is fed to the other
input of the PWM generator. When the current-loop
signal exceeds the voltage-loop signal, the PWM
generator turns off the bipolar output transistor. The next
clock period initiates the next switching cycle,
maintaining the constant frequency current-mode PWM
control.
Pin Description
VIN
VIN provides power to the MOSFETs for the switch
mode regulator section. Due to the high switching
speeds, a 2.2μF capacitor is recommended close to VIN
and the power ground (PGND) pin for bypassing. Please
refer to layout recommendations.
VDD
The VDD pin supplies the power to the internal power to
the control and reference circuitry. The VDD is powered
from VIN. A small 0.1μF capacitor is recommended for
bypassing.
MIC2601/2
EN
The enable pin provides a logic level control of the
output. In the off state, supply current of the device is
greatly reduced (typically <0.1μA). Also, in the off state,
the output drive is placed in a "tri-stated" condition,
where bipolar output transistor is in an “off” or non-
conducting state. Do not drive the enable pin above the
supply voltage.
SS
The SS pin is the soft start pin which allows the
monotonic buildup of output when the MIC2601/2 comes
up during turn on. The SS pin gives the designer the
flexibility to have a desired soft start by placing a
capacitor SS to ground. A 0.1μF capacitor is used for in
the circuit.
FB
The feedback pin (FB) provides the control path to
control the output. For fixed output controller output is
directly connected to feedback (FB) pin.
SW
The switch (SW) pin connects directly to the inductor
and provides the switching current necessary to operate
in PWM mode. Due to the high speed switching and high
voltage associated with this pin, the switch node should
be routed away from sensitive nodes.
PGND
Power ground (PGND) is the ground path for the high
current PWM mode. The current loop for the power
ground should be as small as possible and separate
from the Analog ground (AGND) loop. Refer to the layout
considerations for more details.
AGND
Analog ground (AGND) is the ground path for the biasing
and control circuitry. The current loop for the signal
ground should be separate from the Power ground
(PGND) loop. Refer to the layout considerations for more
details.
September 2009
8
M9999-090909-A
相关PDF资料 |
PDF描述 |
|---|---|
| V28C5T50BF | CONVERTER MOD DC/DC 5V 50W |
| ESC20DRTS | CONN EDGECARD 40POS DIP .100 SLD |
| ECC36DRES | CONN EDGECARD 72POS .100 EYELET |
| MIC2605YML TR | IC REG BOOST ADJ 0.5A 8MLF |
| EBC40DRAI | CONN EDGECARD 80POS R/A .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2602YML | 制造商:Micrel 功能描述:0.2A, 2MHz Wide Input Boost Regulator |
| MIC2602YML TR | 功能描述:直流/直流开关调节器 1.2A 2 MHz Wide Input Range Boost Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC2602YML-TR | 功能描述:Boost Switching Regulator IC Positive Adjustable 4.5V 1 Output 1.2A (Switch) 8-VFDFN Exposed Pad, 8-MLF? 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 功能:升压 输出配置:正 拓扑:升压 输出类型:可调式 输出数:1 电压 - 输入（最小值）:4.5V 电压 - 输入（最大值）:20V 电压 - 输出（最小值/固定）:4.5V 电压 - 输出（最大值）:40V（开关） 电流 - 输出:1.2A（开关） 频率 - 开关:1.92MHz 同步整流器:无 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 供应商器件封装:8-MLF?（2x2） 标准包装:1 |
| MIC2605YML | 制造商:Micrel 功能描述:0.5A 1.2MHz Wide In Boost Reg w Schottky |
| MIC2605YML TR | 功能描述:直流/直流开关调节器 0.5A 1.2 MHz Wide Input Range Boost Regulator w/ Integrated Schottky RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。