- 您现在的位置：买卖IC网 > PDF目录15455 > MIC2755YMM TR (Micrel Inc)IC SUPERVISOR BATT SYSTEM 8-MSOP PDF资料下载
参数资料
| 型号： | MIC2755YMM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 7/10页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR BATT SYSTEM 8-MSOP |
| 标准包装： | 2,500 |
| 类型： | 备用电池电路 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 700 ms |
| 电压 - 阀值： | 可调节/可选择 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2755YMMTR MIC2755YMMTR-ND |
MIC2755
Micrel, Inc.
V BAT(dead) = 2.9V = 1.24V ?
? 1M ? ?
? R9 + 400k ?
R10=400k
1MΩ = R10+R11
?
200
180
160
140
Input Transient
Response (V POF )
Response (V NMI )
R9 = 27k
R8 = 1MΩ – R9 – R10 = 573k
The accuracy of the resistors can be chosen based upon the
accuracy required by the system.
Input Transients
The MIC2755 is inherently immune to very short negative-
going “glitches.” Very brief transients may cross the V BAT(lo)
or V BAT(dead) thresholds without tripping the output(s).
As shown in Figures 3 and 4, the narrower the transient, the
deeper the threshold overdrive that will be ignored by the
MIC2755. The graph represents the typical allowable transient
duration for a given amount of threshold overdrive that will
not cause the corresponding output to change state.
Alternate Con?gurations
The MIC2755 can be used in a variety of ways. It is especially
?exible due to the fact that the NMI comparator is completely
independent. There are other useful con?guration besides
a three-state battery monitor. The NMI comparator can be
used to provide power-fail indication (PFI/PFI), monitor an
auxiliary battery (LBI/LBO), or detect the presence of an ac
adapter.
Voltage Supervisor and Backup Battery Monitor
Figure 5 illustrates the MIC2755 being used as a voltage su-
pervisor and a battery monitor in a 3.3V system with a Lithium
coin-cell backup. The primary voltage monitor is con?gured
as a voltage supervisor with a nominal trip point of 3.034V
and 33mV of hysteresis as set by R1, R2, and R3. The NMI
comparator is used to detect a low-battery condition so the
system is aware that the backup battery is discharged. In
this example, the /NMI output will be asserted if battery volt-
age falls below 2.2V. Manual reset capability can be added
as discussed in the Manual Reset and Con?guration With
Manual Reset sections.
This same con?guration can be used to detect the presence
of an auxiliary power source such as an ac adapter instead
of monitoring a battery. R4 and R5 would be selected such
that the /NMI output is deasserted when the proper input
voltage is applied.
Voltage Supervisor with Power Fail Warning
Figure 6 illustrates the MIC2755 being used as a voltage
supervisor and a power-fail detector in a 3.3V system. The
primary voltage monitor is con?gured as a voltage supervisor
with a nominal trip point of 3.034V and 33mV of hysteresis as
120
100
80
60
40
20
0
0 5 10 15 20 25 30
RESET COMP. OVERDRIVE, V REF –V PTH (mV)
Figure 3. Input Transient Response
Input Transient
120
100
80
60
40
20
0
0 5 10 15 20 25 30 35 40 45
RESET COMP. OVERDRIVE, V REF –V NTH (mV)
Figure 4. Input Transient Response
set by R1, R2, and R3. The NMI comparator is used to detect
an impending power failure such as a low-battery condition
or ac power outage. The /NMI output will be asserted if the
input voltage to the LDO regulator falls below 3.55V. (The
MIC5245 has a speci?ed maximum dropout of 250mV at
150mA output current. If the input voltage falls below 3.55V,
the output may droop.)
By monitoring the input of the LDO regulator, the system re-
ceives the earliest warning of an impending power loss. Manual
reset capability can be added as discussed in the Manual
Reset and Con?guration With Manual Reset sections.
Supervised Boost Converter and Microcontroller or Mi-
croprocessor
In Figures 7 and 8, the MIC2755 is used to monitor the battery
and the MIC3172 is used to maintain the output voltage at
3.3V by boosting the input voltage. When the Li-ion battery
voltage drops to 3.1V, the MIC2755 alerts the microcontroller
or the microprocessor. When the battery voltage drops to
2.9V, the MIC2755 turns off the MIC3172.
January 2006
7
MIC2755
相关PDF资料 |
PDF描述 |
|---|---|
| HSM12DRAH | CONN EDGECARD 24POS R/A .156 SLD |
| HMM12DRAH | CONN EDGECARD 24POS R/A .156 SLD |
| V110C28T100BF | CONVERTER MOD DC/DC 28V 100W |
| GBA44DTMS | CONN EDGECARD 88POS R/A .125 SLD |
| GSA18DTMI | CONN EDGECARD 36POS R/A .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC27600YJL TR | 功能描述:直流/直流开关调节器 36VIN/7A DC-DC Buck Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC27600YJL-TR | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 7A 28-PowerVQFN Variant, 28-MLF? 制造商:microchip technology 系列:Hyper Speed Control?，SuperSwitcher II? 包装:剪切带（CT） 零件状态:有效 功能:降压 输出配置:正 拓扑:降压 输出类型:可调式 输出数:1 电压 - 输入（最小值）:4.5V 电压 - 输入（最大值）:36V 电压 - 输出（最小值/固定）:0.8V 电压 - 输出（最大值）:5.5V 电流 - 输出:7A 频率 - 开关:300kHz 同步整流器:是 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:28-PowerVQFN 变式，28-MLF? 供应商器件封装:28-MLF?（5x6） 标准包装:1 |
| MIC27600YML | 制造商:Micrel Inc 功能描述:DC-DC Buck Regulator 36V 7A Adj 1% MLF28 |
| MIC2772-L2L3YML TR | 功能描述:监控电路 Dual Voltage Supervisor with Manual Reset and Active-Low Open-Drain Outputs 4.63V / 20ms - 4.63V / 140ms - 2mm x 2mm MLF - Lead Free RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MIC2772-L3L3BML TR | 功能描述:IC VOLTAGE SUPERVISOR DUAL 8MLF RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:标准传输延迟为 60 µs 电压 - 阀值:3V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 其它名称:LM8364BALMF30DKR |
发布紧急采购，3分钟左右您将得到回复。