参数资料
型号: MIC2775-17YM5 TR
厂商: Micrel Inc
文件页数: 5/7页
文件大小: 0K
描述: IC SUPERVISOR MICROPOWER SOT23-5
标准包装: 3,000
类型: 简单复位/加电复位
监视电压数目: 1
输出: 补充型
复位: 高有效/低有效
复位超时: 最小为 140 ms
电压 - 阀值: 1.69V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: SC-74A,SOT-753
供应商设备封装: SOT-23-5
包装: 带卷 (TR)
其它名称: MIC2775-17YM5TR
MIC2775-17YM5TR-ND
MIC2775
Functional Diagram
V DD
Micrel, Inc.
R
Q
/RST
V DD
I PU
V REF
Delay
Line
One Shot
S /Q
RST
/MR
GND
MIC2775
Functional Description
V DD Input
The V DD pin is both the power supply terminal and a monitored
input voltage. The voltage at this pin is continually compared
against the internal reference. The trip-point at which a reset
occurs is factory programmed. A reset is triggered if and
when V DD falls below the trip-point. Hysteresis is employed
to prevent chattering due to noise. The comparator on the
V DD input is relatively immune to very brief negative-going
transients.
RST, /RST Reset Outputs
Typically, the MIC2775 is used to monitor the power supply
of intelligent circuits such as microcontrollers and micropro -
cessors. By connecting the appropriate reset output of a
MIC2775 to the reset input of a μC or μP, the processor will
be properly reset at power-on and during power-down and
brown-out conditions. In addition, asserting /MR, the manual
reset input, will activate the reset function.
The reset outputs are asserted any time /MR is asserted or
if V DD drops below the threshold voltage. The reset outputs
remain asserted for t RST (min) after V DD subsequently returns
above the threshold boundary and/or /MR is released. A reset
pulse is also generated at power-on. Hysteresis is included
in the comparator to prevent chattering of the outputs due
to noise.
/MR, Manual Reset Input
The ability to initiate a reset via external logic or a manual
switch is provided in addition to the MIC2775’s automatic su-
pervisory functions. Driving the /MR input to a logic low causes
an immediate and unconditional reset to occur. Assuming
V DD is within tolerance when /MR is released (returns high),
the reset outputs will be de-asserted no less than t RST later.
/MR may be driven by a logic signal or mechanical switch.
Typically, a momentary push-button switch is connected
such that /MR is shorted to ground when the switch contacts
close. The switch may be connected directly between /MR
and GND. /MR has an internal 100nA pull-up current to V DD
and may be left open if unused.
June 2009
5
MIC2775
相关PDF资料
PDF描述
ADM1818-20AKSZ-RL7 IC MONITOR RESET 2.55V SC-70-3
ADM1818-10AKSZ-RL7 IC MONITOR RESET 2.88V SC-70-3
RBM08DCMI-S288 CONN EDGECARD 16POS .156 EXTEND
ADM1817-5ARTZ-RL7 IC MONITOR RESET 3.06V SOT23
ADM1817-R23ARTZ-R7 IC MONITOR RESET 2.31V SOT23
相关代理商/技术参数
参数描述
MIC2775-22BM5 TR 功能描述:IC SUPERVISOR MICROPOWER SOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:标准传输延迟为 60 µs 电压 - 阀值:3V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A,SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 其它名称:LM8364BALMF30DKR
MIC2775-22BM5TR 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel 制造商:RF Micro Devices Inc 功能描述:
MIC2775-22YM5 TR 功能描述:监控电路 Single Voltage Supervisor with Dual Active-High and Low Push-Pull Outputs, Manual Reset, 2.25V Threshold, 140ms Reset SOT23-5 (Lead Free) RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MIC2775-23BM5 制造商:Rochester Electronics LLC 功能描述:- Bulk
MIC2775-23BM5 TR 功能描述:IC SUPERVISOR MICROPOWER SOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:低有效 复位超时:标准传输延迟为 60 µs 电压 - 阀值:3V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A,SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 其它名称:LM8364BALMF30DKR