- 您现在的位置：买卖IC网 > PDF目录20631 > MIC2800-A4SYML TR (Micrel Inc)IC REG TRPL BUCK/LINEAR 16MLF PDF资料下载
参数资料
| 型号： | MIC2800-A4SYML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 18/20页 |
| 文件大小： | 506K |
| 描述： | IC REG TRPL BUCK/LINEAR 16MLF |
| 标准包装： | 5,000 |
| 拓扑： | 降压（降压）（1），线性（LDO）（2） |
| 功能： | 任何功能 |
| 输出数： | 3 |
| 频率 - 开关： | 2MHz |
| 电压/电流 - 输出 1： | 可调，600mA |
| 电压/电流 - 输出 2： | 1.2V，300mA |
| 电压/电流 - 输出 3： | 3.3V，300mA |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VFQFN，16-MLF? |
| 供应商设备封装： | 16-MLF?（4x4） |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2800-A4SYMLTR MIC2800-A4SYMLTR-ND |
Micrel, Inc.
MIC2800
September 2007
18
M9999-090507-C
SW
The switch (SW) pin connects directly to the inductor
and provides the switching current necessary to operate
in PWM mode. Due to the high speed switching on this
pin, the switch node should be routed away from
sensitive nodes.
PGND
Power ground (PGND) is the ground path for the high
current PWM mode. The current loop for the power
ground should be as small as possible. Refer to the
layout considerations for more details.
SGND
Signal ground (SGND) is the ground path for the biasing
and control circuitry. The current loop for the signal
ground should be as small as possible. Refer to the
layout considerations for more details.
CSET
The SET pin is a current source output that charges a
capacitor that sets the delay time for the power-on reset
output from low to high. The delay for POR high to low
(detecting an undervoltage on any of the outputs) is
always minimal. The current source of 1.25礎 charges a
capacitor up from 0V. When the capacitor reaches
1.25V, the output of the POR is allowed to go high. The
delay time in micro seconds is equal to the Cset in
picofarads.
POR Delay (祍) = CSET (pF)
CBYP
The internal reference voltage can be bypassed with a
capacitor to ground to reduce output noise and increase
power supply rejection (PSRR). A quick-start feature
allows for quick turn-on of the output voltage. The
recommended nominal bypass capacitor is 0.1礔, but it
can be increased, which will also result in an increase to
the start-up time.
Output Capacitor
LDO1 and LDO2 outputs require a 2.2礔 ceramic output
capacitor for stability. The DC/DC switch mode regulator
requires a 2.2礔 ceramic output capacitor to be stable.
All output capacitor values can be increased to improve
transient response, but performance has been optimized
for a 2.2礔 ceramic on the LDOs and the DC/DC.
X7R/X5R dielectric-type ceramic capacitors are
recommended because of their temperature
performance. X7R-type capacitors change capacitance
by 15% over their operating temperature range and are
the most stable type of ceramic capacitors. Z5U and
Y5V dielectric capacitors change value by as much as
50% to 60% respectively over their operating
temperature ranges.
Input Capacitor
A minimum 1礔 ceramic is recommended on the VIN pin
for bypassing. X5R or X7R dielectrics are recommended
for the input capacitor. Y5V dielectrics lose most of their
capacitance over temperature and are therefore, not
recommended. A minimum 1礔 is recommended close
to the VIN and PGND pins for high frequency filtering.
Smaller case size capacitors are recommended due to
their lower ESR and ESL. Please refer to layout
recommendations for proper layout of the input
capacitor.
Inductor Selection
The MIC2800 is designed for use with a 2.2礖 inductor.
Proper selection should ensure the inductor can handle
the maximum average and peak currents required by the
load. Maximum current ratings of the inductor are
generally given in two methods; permissible DC current
and saturation current. Permissible DC current can be
rated either for a 40癈 temperature rise or a 10% to 20%
loss in inductance. Ensure that the inductor selected can
handle the maximum operating current. When saturation
current is specified, make sure that there is enough
margin that the peak current will not saturate the
inductor. Peak inductor current can be calculated as
follows:
L
f
2
V
V
1
V
I
I
IN
OUT
OUT
OUT
PK
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
?/DIV>
+
=
相关PDF资料 |
PDF描述 |
|---|---|
| T491B107K006AT | CAP TANT 100UF 6.3V 10% 1411 |
| RSM40DTMH-S189 | CONN EDGECARD 80POS R/A .156 SLD |
| RMM03DSEN | CONN EDGECARD 6POS .156 EYELET |
| MIC2810-CGJYML TR | IC REG TRPL BUCK/LINEAR 16-MLF |
| VI-J6W-CX-F4 | CONVERTER MOD DC/DC 5.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC280-0BM6 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MIC280-0BM6 TR | 功能描述:IC SUPERVISOR THERMAL SOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:IttyBitty® 标准包装:2,500 系列:SilentSense™ 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-55°C ~ 125°C，外部传感器 精确度:±2°C 本地（最大），±3°C 远程（最大） 拓扑:ADC（三角积分型），比较器，寄存器库 输出类型:I²C?/SMBus? 输出警报:是 输出风扇:是 电源电压:2.7 V ~ 5.5 V 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR) 其它名称:MIC284-2BMMTRMIC284-2BMMTR-ND |
| MIC280-0BM6TR | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| MIC2800-D24MYML | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: 制造商:Micrel Inc 功能描述: |
| MIC2800-D24MYML TR | 功能描述:线性稳压器 - 标准 DC-DC + 2 Linear Regulators with LowQ Mode (Lead Free) RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
发布紧急采购，3分钟左右您将得到回复。