- 您现在的位置：买卖IC网 > PDF目录224284 > MIC2810-1.2/1.8/2.6YML (MICREL INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC16 PDF资料下载
参数资料
| 型号： | MIC2810-1.2/1.8/2.6YML |
| 厂商： | MICREL INC |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC16 |
| 封装： | 3 X 3 MM, MLF-16 |
| 文件页数： | 6/18页 |
| 文件大小： | 508K |
| 代理商： | MIC2810-1.2/1.8/2.6YML |
Micrel, Inc.
MIC2810
April 2007
14
M9999-041107-B
SW
The switch (SW) pin connects directly to the inductor
and provides the switching current necessary to operate
in PWM mode. Due to the high speed switching on this
pin, the switch node should be routed away from
sensitive nodes.
PGND
Power ground (PGND) is the ground path for the high
current PWM mode. The current loop for the power
ground should be as small as possible.
SGND
Signal ground (SGND) is the ground path for the biasing
and control circuitry. The current loop for the signal
ground should be as small as possible.
CSET
The CSET pin is a current source output that charges a
capacitor that sets the delay time for the power-on reset
output from low to high. The delay for POR high to low
(detecting an undervoltage on any of the outputs) is
always minimal. The current source of 1.25A charges a
capacitor up from 0V. When the capacitor reaches
1.25V, the output of the POR is allowed to go high. The
delay time in microseconds is equal to the Cset in
picofarads.
POR Delay (s) = CSET (pF)
Component Selection
Output Capacitor
LDO1 and LDO2 outputs require a 2.2F ceramic output
capacitor for stability. The DC/DC switch mode regulator
also requires a 2.2F ceramic output capacitor to be
stable. All output capacitor values can be increased to
improve transient response, but performance has been
optimized for a 2.2F ceramic on the LDOs and the
DC/DC regulator. X7R/X5R dielectric-type ceramic
capacitors
are
recommended
because
of
their
temperature performance. X5R/X7R-type capacitors
change capacitance by 15% over their operating
temperature range and are the most stable type of
ceramic capacitors. Z5U and Y5V dielectric capacitors
change value by as much as 50% to 60% respectively
over their operating temperature ranges.
Input Capacitor
A minimum 1F ceramic, 4.7F recommended, should
be placed as close as possible to the VIN pin for optimal
bypassing. X5R or X7R dielectrics are recommended for
the input capacitor. Y5V dielectrics lose most of their
capacitance over temperature and are therefore, not
recommended. A minimum 1F is recommended close
to the VIN and PGND pins for high frequency filtering.
Smaller case size capacitors are recommended due to
their lower ESR and ESL. Please refer to the PCB layout
section for an example of an appropriate circuit layout.
Inductor Selection
The MIC2810 is designed for use with a 2.2H inductor.
Proper selection should ensure the inductor can handle
the maximum average and peak currents required by the
load. Maximum current ratings of the inductor are
generally given in two methods; permissible DC current
and saturation current. Permissible DC current can be
rated either for a 40°C temperature rise or a 10% to 20%
loss in inductance. Ensure that the inductor selected can
handle the maximum operating current. When saturation
current is specified, make sure that there is enough
margin that the peak current will not saturate the
inductor. Peak inductor current can be calculated as
follows:
L
f
2
V
1
V
I
IN
OUT
PK
×
+
=
IPK:
Peak Inductor Current
IOUT:
Output/Load Current
VIN:
Input Voltage
VOUT:
Output Voltage
f:
Switching Frequency of PWM Regulator
L:
Inductor Value
相关PDF资料 |
PDF描述 |
|---|---|
| MIC29153BT | High-Current Low-Dropout Regulators |
| MIC29153BU | High-Current Low-Dropout Regulators |
| MIC29301-12BT | High-Current Low-Dropout Regulators |
| MIC29301-12BU | High-Current Low-Dropout Regulators |
| MIC29203BT | 1.24 V-26 V ADJUSTABLE POSITIVE LDO REGULATOR, 0.75 V DROPOUT, PSFM5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2810-1JGMYML TR | 功能描述:线性稳压器 - 标准 DC-DC + 2 Linear Regulators with LowQ mode and POR (Lead-Free) RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
| MIC2810-44MYML | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
| MIC2810-44MYML TR | 功能描述:线性稳压器 - 标准 DC-DC + 2 Linear Regulators with LowQ mode and POR (Lead-Free) RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
| MIC2810-44MYML-TR | 功能描述:Linear And Switching Voltage Regulator IC 3 Output Step-Down (Buck) (1), Linear (LDO) (2) 2MHz 16-VFQFN, 16-MLF? 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 拓扑:降压（降压）（1），线性（LDO）（2） 功能:任何功能 输出数:3 频率 - 开关:2MHz 电压/电流 - 输出 1:1.2V，600mA 电压/电流 - 输出 2:1.2V，300mA 电压/电流 - 输出 3:2.8V，300mA 带 LED 驱动器:无 带监控器:无 带定序器:无 电压 - 电源:1.65 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VFQFN，16-MLF? 供应商器件封装:16-MLF?（4x4） 标准包装:1 |
| MIC2810-4GKYML TR | 功能描述:线性稳压器 - 标准 DC-DC + 2 Linear Regulators with LowQ mode and POR (Lead-Free) RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
发布紧急采购，3分钟左右您将得到回复。