参数资料
| 型号： | MIC2821-4GJLYML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 12/17页 |
| 文件大小： | 0K |
| 描述： | IC PWR MGMT DGTL TRPL LDO 16-MLF |
| 标准包装： | 1 |
| 应用： | 手持/移动设备 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VFQFN 裸露焊盘，16-MLF? |
| 供应商设备封装： | 16-MLF?（4x4） |
| 包装： | 标准包装 |
| 产品目录页面： | 1086 (CN2011-ZH PDF) |
| 其它名称： | 576-3083-6 |
V OUT ( 1 ?
)
I PK = I OUT +
Efficiency _ % = ?
? × 100
Micrel, Inc.
Applications Information
The MIC2811 and MIC2821 are power management ICs
with a single integrated step-down regulator and three
low dropout regulators. LDO1, LDO2, and LDO3 are
300mA low dropout regulators supplied by their own
independent input voltage pins. The supply to LDO3
(V IN ) also powers the bias circuitry and must be available
for any output to be operational. This supply requires an
external connection to DVIN. The step-down regulator is
a 2MHz 600mA PWM power supply, using small values
of L and C operating at over 90% efficiency.
DVIN/VIN/VIN1/VIN2
All four regulators, the switch mode regulator, LDO1,
LDO2, and LDO3 have their own unique input voltage
supply pin. VIN provides power to LDO3 and internal
circuitry shared by all the regulators and therefore must
be available for any of the regulators to operate properly.
DVIN and VIN must be tied together and have a
minimum input voltage of 2.7V. Inputs to LDO1 (VIN1)
and LDO2 (VIN2) can go as low as 1.65V, but should
never exceed the VIN and DVIN input voltage. Due to
the high switching speeds, a 1 μ F input capacitor is
recommended close to the DVIN, decoupled to the
PGND pin.
LDO1
Regulated output voltage of LDO1. Power is provided by
VIN1 and enabled through EN1. Recommended output
capacitance is 2.2 μ F, decoupled to the SGND pin.
LDO2
Regulated output voltage of LDO2. Power is provided by
VIN2 and enabled through EN2. Recommended output
capacitance is 2.2 μ F, decoupled to the SGND pin.
LDO3
Regulated output voltage of LDO3. Power is provided by
VIN and enabled through EN (MIC2811) or EN3
(MIC2821). Recommended output capacitance is 2.2 μ F,
decoupled to the SGND pin.
SW
The switch (SW) pin connects directly to the inductor
and provides the switching current necessary to operate
in PWM mode. Due to the high speed switching on this
pin, the switch node should be routed away from
sensitive nodes.
DC/DC Output Capacitor
The DC/DC regulator requires an output capacitor for
proper operation. Values of greater than 2.2 μ F improve
transient response and noise reduction at high
frequency. X7R/X5R dielectric-type ceramic capacitors
are recommended because of their superior temperature
MIC2811/2821
performance. X7R-type capacitors change capacitance
by 15% over their operating temperature range and are
the most stable type of ceramic capacitors. Z5U and
Y5V dielectric capacitors change value by as much as
50% to 60% respectively over their operating
temperature ranges and for that reason are not
recommended. Larger output capacitances can be
achieved by placing tantalum or aluminum electrolytics
in parallel with the ceramic capacitor. For example, a
100 μ F electrolytic in parallel with a 10 μ F ceramic can
provide the transient and high frequency noise
performance of a 100 μ F ceramic at a significantly lower
cost. Specific undershoot/overshoot performance will
depend on both the values and ESR/ESL of the
capacitors.
Inductor Selection
Inductor selection will be determined by the following
(not necessarily in the order of importance);
? Inductance
? Rated current value
? Size requirements
? DC resistance (DCR)
The MIC2811 and MIC2821 are designed for use with a
2.2 μ H inductor. Maximum current ratings of the inductor
are generally given in two methods; permissible DC
current and saturation current. Permissible DC current
can be rated either for a 40°C temperature rise or a 10%
to 20% loss in inductance. Ensure the inductor selected
can handle the maximum operating current. When
saturation current is specified, make sure that there is
enough margin that the peak current will not saturate the
inductor. Peak inductor current can be calculated as
follows:
V OUT
V IN
2 × f × L
The size requirements refer to the area and height
requirements that are necessary to fit a particular
design. Please refer to the inductor dimensions on their
datasheet.
DC resistance is also important. While DCR is inversely
proportional to size, DCR can represent a significant
efficiency loss.
Efficiency Considerations
Efficiency is defined as the amount of useful output
power, divided by the amount of power supplied.
? Vout × Iout ?
? Vin × Iin ?
Maintaining high efficiency serves two purposes. It
reduces power dissipation in the power supply, reducing
the need for heat sinks and thermal design
April 2008
12
M9999-042208-A
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2826-A0YMT TR | IC PWR MANAGER PROG 4OUT 14-TMLF |
| MIC28500YJL TR | IC REG BUCK SYNC ADJ 4A 28MLF |
| MIC28510YJL TR | IC REG BUCK SYNC ADJ 4A 28MLF |
| MIC29152WD TR | IC REG LDO ADJ 1.5A TO-252-5 |
| MIC2920A-12WS | IC REG LDO 12V .4A SOT-223 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2821-4GMSYML | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: 制造商:Micrel Inc 功能描述: |
| MIC2821-4GMSYML TR | 功能描述:直流/直流开关转换器 Single DC/DC + 3 LDOs w/ Indep Enables RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MIC2821-4GMSYML-TR | 功能描述:Handheld/Mobile Devices PMIC 16-MLF? (4x4) 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 应用:手持/移动设备 电流 - 电源:- 电压 - 电源:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:16-VFQFN 裸露焊盘，16-MLF? 供应商器件封装:16-MLF?（4x4） 标准包装:1 |
| MIC2826-A0YMT TR | 功能描述:直流/直流开关调节器 Single 500mA Step-Down and Triple 150mA LDOs with I2C Voltage Control & Sequencing RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC2826-A0YMT-TR | 功能描述:Processor PMIC 14-TMLF? (2.5x2.5) 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 应用:处理器 电流 - 电源:- 电压 - 电源:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-UFQFN 裸露焊盘，14-TMLF? 供应商器件封装:14-TMLF?（2.5x2.5） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。