参数资料
型号: MIC284-3YMM TR
厂商: Micrel Inc
文件页数: 7/20页
文件大小: 904K
描述: IC SUPERVISOR THERM 2ZONE 8-MSOP
标准包装: 2,500
系列: SilentSense™
功能: 温度监控系统(传感器)
传感器类型: 内部和外部
感应温度: -55°C ~ 125°C,外部传感器
精确度: ±2°C 本地(最大),±3°C 远程(最大)
拓扑: ADC(三角积分型),比较器,寄存器库
输出类型: I²C?/SMBus?
输出警报:
输出风扇:
电源电压: 2.7 V ~ 5.5 V
工作温度: -55°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 8-TSSOP,8-MSOP(0.118",3.00mm 宽)
供应商设备封装: 8-MSOP
包装: 带卷 (TR)
其它名称: MIC284-3YMMTR
MIC284-3YMMTR-ND
September 2005
7
MIC284
MIC284
Micrel, Inc.
mask bit.
/CRIT: Over-temperature events are indicated to external 
circuitry via this output. This output is open-drain and may
be wire-ORed with other open-drain signals. Most systems
will require a pull-up resistor or current source on this pin.
T1: This pin connects to an off-chip PN diode junction, for
monitoring the junction temperature at a remote location.
The remote diode may be an embedded thermal sens-
ing junction in an integrated circuit so equipped (such
as Intel's Pentium III), or a discrete 2N3906-type bipolar
transistor with base and collector tied together.
Temperature Measurement
The temperature-to-digital converter is built around a switched
current source and an eight-bit analog-to-digital converter.
Each diode's temperature is calculated by measuring its for-
ward voltage drop at two different current levels. An internal
multiplexer directs the MIC284's current source output to either
an internal or external diode junction. The MIC284 uses twos-
complement data to represent temperatures. If the MSB of a
temperature value is zero, the temperature is zero or positive.
If the MSB is one, the temperature is negative. More detail
on this is given in the "Temperature Data Format" section
below. A temperature event results if the value in either of
the temperature result registers (TEMPx) becomes greater
than the value in the corresponding temperature setpoint
register (T_SETx). Another temperature event occurs if and
when the measured temperature subsequently falls below
the temperature hysteresis setting in T_HYSTx.
During normal operation the MIC284 continuously performs
temperature-to-digital conversions, compares the results
against the setpoint registers, and updates the states of /INT,
/CRIT, and the status bits accordingly. The remote zone is
converted rst, followed by the local zone. The states of /INT,
/CRIT, and the status bits are updated after each measure-
ment is taken. The remote diode junction connected to T1
may be embedded in an integrated circuit such as a CPU,
ASIC, or graphics processor, or it may be a diode-connected
discrete transistor.
Diode Faults
The MIC284 is designed to respond in a failsafe manner to
hardware faults in the external sensing circuitry. If the con-
nection to the external diode is lost or the sense line (T1) is
shorted to VDD or ground, the temperature data reported
by the A/D converter will be forced to its full-scale value
(+127癈). This will cause a temperature event to occur if
T_SET1 or CRIT1 are set to any value less than 127癈 (7F
h
 
= 0111 1111
b
). An interrupt will be generated on /INT if so
enabled. The temperature reported for the external zone will
remain +127癈 until the fault condition is cleared. This fault
detection mechanism requires that the MIC284 complete
the number of conversion cycles specied by Fault_Queue.
The part will therefore require one or more conversion cycles
following power-on or a transition from shutdown to normal
operation before reporting an external diode fault.
Serial Port Operation
The MIC284 uses standard SMBus Write_Byte and Read_Byte
operations for communication with its host. The SMBus
Write_Byte operation involves sending the devices slave
address (with the R/W bit low to signal a write operation),
followed by a command byte and a data byte. The SMBus
Read_Byte operation is similar, but is a composite write and
read operation: the host rst sends the devices slave address
followed by the command byte, as in a write operation. A
new start bit must then be sent to the MIC284, followed by
a repeat of the slave address with the R/W bit (LSB) set to
the high (read) state. The data to be read from the part may
then be clocked out.
The command byte is eight bits wide. This byte carries the
address of the MIC284 register to be operated upon, and is
stored in the parts pointer register. The pointer register is
an internal write-only register. The command byte (pointer
register) values corresponding to the various MIC284 register
addresses are shown in Table 2. Command byte values other
than those explicitly shown are reserved, and should not be
used. Any command byte sent to the MIC284 will persist in
the pointer register indenitely until it is overwritten by another
command byte. If the location latched in the pointer register
from the last operation is known to be correct (i.e., points
to the desired register), then the Receive_Byte procedure
may be used. To perform a Receive_Byte, the host sends
an address byte to select the MIC284, and then retrieves the
data byte. Figures 1 through 3 show the formats for these
procedures.
相关PDF资料
PDF描述
S820K29SL0N6TK6R CAP CER 82PF 1KV 10% RADIAL
NMK0509SAC CONV DC/DC 2W 5VIN 9VOUT SIP
TAP155K050CRW CAP TANT 1.5UF 50V 10% RADIAL
IRU1206-33CD IC REG LDO 3.3V 1A D-PAK
V48A3V3E264BF2 CONVERTER MOD DC/DC 3.3V 264W
相关代理商/技术参数
参数描述
MIC2843YMT TR 功能描述:LED照明驱动器 Six Channel Current Sink in 2x2 Thin MLF RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MIC2843YMT-TR 功能描述:LED 驱动器 IC 6 输出 线性 PWM 调光 20mA 10-TMLF?(2x2) 制造商:microchip technology 系列:- 包装:剪切带(CT) 零件状态:停产 类型:线性 拓扑:- 内部开关:是 输出数:6 电压 - 供电(最低):3V 电压 -?供电(最高):5.5V 电压 - 输出:- 电流 - 输出/通道:20mA 频率:- 调光:PWM 应用:背光,照相机闪光灯 工作温度:-40°C ~ 125°C (TJ) 安装类型:表面贴装 封装/外壳:10-UFDFN 裸露焊盘,10-TMLF? 供应商器件封装:10-TMLF?(2x2) 标准包装:1
MIC2844AYMT TR 功能描述:LED照明驱动器 6 Channel Linear WLED Driver with Digital Control RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MIC2844AYMT-TR 功能描述:LED 驱动器 IC 6 输出 线性 单线 调光 20mA 10-TMLF?(2x2) 制造商:microchip technology 系列:- 包装:剪切带(CT) 零件状态:停产 类型:线性 拓扑:- 内部开关:是 输出数:6 电压 - 供电(最低):3V 电压 -?供电(最高):5.5V 电压 - 输出:- 电流 - 输出/通道:20mA 频率:- 调光:单线 应用:背光,照相机闪光灯 工作温度:-40°C ~ 125°C (TJ) 安装类型:表面贴装 封装/外壳:10-UFDFN 裸露焊盘,10-TMLF? 供应商器件封装:10-TMLF?(2x2) 标准包装:1
MIC2845A-MFYMT TR 功能描述:LED照明驱动器 6 Channel Linear WLED Driver + 2 LDOs with PWM Control RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N