- 您现在的位置：买卖IC网 > Datasheet目录343 > MIC2846A-MFYMT TR (Micrel Inc)IC LED DRIVR WHITE BCKLGT 14TMLF Datasheet资料下载
参数资料
| 型号： | MIC2846A-MFYMT TR |
| 厂商： | Micrel Inc |
| 文件页数： | 11/19页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR WHITE BCKLGT 14TMLF |
| 标准包装： | 1 |
| 拓扑： | 线性（LDO） |
| 输出数： | 6 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，闪灯/白光 |
| 类型 - 次要： | 白色 LED |
| 电源电压： | 3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-UFQFN 裸露焊盘，14-TMLF? |
| 供应商设备封装： | 14-TMLF?（2.5x2.5） |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 125°C |
| 产品目录页面： | 1082 (CN2011-ZH PDF) |
| 其它名称： | 576-3477-6 |
Micrel Inc.
VIN
The input supply (VIN) provides power to the LDOs, the
linear LED drivers and the control circuitry. The V IN
operating range is 3V to 5.5V. A minimum bypass
capacitor of 1μF should be placed close to the input
(VIN) pin and the ground (GND) pin. Refer to the layout
recommendations section for details on placing the input
capacitor (C1).
LDO1/LDO2
The output pins for LDO one and LDO two are labeled
LDO1 and LDO2, respectively. A minimum of 1μF
bypass capacitor should be placed as close as possible
to the output pin of each LDO. Refer to the layout
recommendations section for details on placing the
output capacitor (C2, C3) of the LDOs.
EN1/EN2
A logic high signal on the enable pin activates the LDO
output voltage of the device. A logic low signal on the
enable pin deactivates the output and reduces supply
current to less than 1μA. EN1 controls LDO1 and EN2
controls LDO2. Do not leave these control pins floating.
DC
The DC pin is used to enable and control dimming of the
linear drivers on the MIC2846A. See the MIC2846A
Digital Dimming Interface in the Application Information
section for details. Pulling the DC pin low for more than
1260 μ s puts the MIC2846A into a low I Q sleep mode.
The DC pin cannot be left floating; a floating enable pin may
cause an indeterminate state on the outputs. A 200k ? pull
down resistor is recommended.
R SET
The R SET pin is used by connecting a R SET resistor to
ground to set the peak current of the linear LED
driver. The average LED current can be calculated
by the equation (1).
I LED (mA) = 410 * ADC / R SET (k ? ) (1)
ADC is the average duty cycle of the LED current
controlled by the single-wire digital dimming. See Table
1 for ADC values. When the device is fully on the
average duty cycle equals 100% (ADC=1). A plot of I LED
versus R SET at 100% duty cycle is shown in Figure 2.
MIC2846A
Figure 2. Peak LED Current vs. R SET (100% Duty Cycle)
D1-D6
The D1 through D6 pins are the LED driver for LED 1
through 6, respectively. The anodes of the LEDs are
connected to VIN and the cathodes of the LEDs are
connected to D1 through D6. When operating with less
than six LEDs, leave the unused D pins unconnected.
The six LED channels are independent of one another
and may be combined or used separately. During start-
up, the D1 through D6 channels are turned on in
synchronization at around 250μs apart.
GND
The ground pin is the ground path for the linear drivers
and LDOs. The ground of the input capacitor should be
routed with low impedance traces to the GND pin and
made as short as possible. Refer to the layout
recommendations for more details.
April 2010
11
M9999-041210-D
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2981/82YWM TR | IC SOURCE DRIVER ARRAY HC 18SOIC |
| MIC2981/82YWM | IC DRIVER ARRAY HV/HC 8CH 18SOIC |
| MIC3201YME | IC LED DRIVER 8ESOIC |
| MIC3202YME | IC LED DVR HB 37V 1A 8-SOIC |
| MIC3203YM | IC LED DRIVER CTLR HB 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2846A-MGYMT TR | 功能描述:LED照明驱动器 6 Channel Linear WLED Driver + 2 LDOs with Digital Control RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MIC2846A-MGYMT-TR | 功能描述:LED 驱动器 IC 6 输出 线性 20mA 14-TMLF?（2.5x2.5） 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 类型:线性 拓扑:- 内部开关:是 输出数:6 电压 - 供电（最低）:3V 电压 -?供电（最高）:5.5V 电压 - 输出:- 电流 - 输出/通道:20mA 频率:- 调光:- 应用:背光 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:14-UFQFN 裸露焊盘，14-TMLF? 供应商器件封装:14-TMLF?（2.5x2.5） 标准包装:1 |
| MIC2846A-PGYMT TR | 功能描述:LED照明驱动器 6 Channel Linear WLED Driver + 2 LDOs with Digital Control RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MIC2846A-PGYMT-TR | 功能描述:LED 驱动器 IC 6 输出 线性 20mA 14-TMLF?（2.5x2.5） 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 类型:线性 拓扑:- 内部开关:是 输出数:6 电压 - 供电（最低）:3V 电压 -?供电（最高）:5.5V 电压 - 输出:- 电流 - 输出/通道:20mA 频率:- 调光:- 应用:背光 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:14-UFQFN 裸露焊盘，14-TMLF? 供应商器件封装:14-TMLF?（2.5x2.5） 标准包装:1 |
| MIC2846A-PPYMT TR | 功能描述:LED照明驱动器 6 Channel Linear WLED Driver + 2 LDOs with Digital Control RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。