- 您现在的位置：买卖IC网 > PDF目录17424 > MIC28500 2A EV (Micrel Inc)BOARD EVAL FOR MIC28500 2A PDF资料下载
参数资料
| 型号： | MIC28500 2A EV |
| 厂商： | Micrel Inc |
| 文件页数： | 22/29页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR MIC28500 2A |
| 标准包装： | 1 |
| 系列： | Hyper Speed Control™，SuperSwitcher II™ |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 12V |
| 电流 - 输出： | 2A |
| 输入电压： | 30 ~ 75V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 250kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MIC28500 |
| 其它名称： | 576-4019 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页
Micrel, Inc.
MIC28500
PCB Layout Guidelines
Warning!!! To minimize EMI and output noise, follow
these layout recommendations.
PCB Layout is critical to achieve reliable, stable and
efficient performance. A ground plane is required to
control EMI and minimize the inductance in power,
signal and return paths. Thickness of the copper planes
is also important in terms of dissipating heat. The 2oz
copper thickness is adequate from thermal point of view
?
?
placed in parallel with the input capacitor.
If a Tantalum input capacitor is placed in parallel
with the input capacitor, it must be recommended for
switching regulator applications and the operating
voltage must be derated by 50%.
In “Hot-Plug” applications, a Tantalum or Electrolytic
bypass capacitor must be used to limit the over-
voltage spike seen on the input supply with power is
suddenly applied.
and also thick copper plain helps in terms of noise
Inductor
immunity. Keep in mind thinner planes can be easily
penetrated by noise
The following guidelines should be followed to insure
proper operation of the MIC28500 converter.
?
?
?
Keep the inductor connection to the switch node
(SW) short.
Do not route any digital lines underneath or close to
the inductor.
Keep the switch node (SW) away from the feedback
IC
?
?
?
?
The 2.2μF ceramic capacitor, which is connected to
the VDD pin, must be located right at the IC. The
VDD pin is very noise sensitive and placement of the
capacitor is very critical. Use wide traces to connect
to the VDD and PGND pins.
The signal ground pin (SGND) must be connected
directly to the ground planes. Do not route the
SGND pin to the PGND Pad on the top layer.
Place the IC close to the point of load (POL).
Use fat traces to route the input and output power
lines.
?
?
?
(FB) pin.
The CS pin should be connected directly to the SW
pin to accurate sense the voltage across the low-
side MOSFET.
To minimize noise, place a ground plane underneath
the inductor.
The inductor can be placed on the opposite side of
the PCB with respect to the IC. It does not matter
whether the IC or inductor is on the top or bottom as
long as there is enough air flow to keep the power
components within their temperature limits. The
input and output capacitors must be placed on the
same side of the board as the IC.
?
Signal and power grounds should be kept separate
and connected at only one location.
Output Capacitor
? Use a wide trace to connect the output capacitor
Input Capacitor
? Place the input capacitor next to the power pins.
? Place the input capacitors on the same side of the
board and as close to the IC as possible.
? Keep both the PVIN pin and PGND connections
short.
? Place several vias to the ground plane close to the
input capacitor ground terminal.
?
?
ground terminal to the input capacitor ground
terminal.
Phase margin will change as the output capacitor
value and ESR changes. Contact the factory if the
output capacitor is different from what is shown in
the BOM.
The feedback trace should be separate from the
power trace and connected as close as possible to
the output capacitor. Sensing a long high current
?
Use either X7R or X5R dielectric input capacitors.
Do not use Y5V or Z5U type capacitors.
load trace can degrade the DC load regulation.
RC Snubber
?
Do not replace the ceramic input capacitor with any
other type of capacitor. Any type of capacitor can be
June 2011
22
?
Place the RC snubber on either side of the board
and as close to the SW pin as possible.
M9999-060311-B
相关PDF资料 |
PDF描述 |
|---|---|
| CT4BK18-C | 4" BLACK 18LB CABLE TIE |
| CT8NT18-C | 8" NATURAL 18LB CABLE TIE |
| F950J337MBAAQ2 | CAP TANT 330UF 6.3V 20% SMD |
| BY253P-E3/73 | DIODE 3A 600V DO-201AD |
| 195D475X9015V8T | CAP TANT 4.7UF 15V 10% 1410 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC28500YJL TR | 功能描述:直流/直流开关调节器 75V/4A DC-DC Buck Regulator with HSC RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC28500YJLTR | 制造商:Micrel 功能描述:Conv DC DC Step Down 0.8 12V 28 Pin MLF |
| MIC28500YJL-TR | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 4A 28-PowerVQFN Variant, 28-MLF? 制造商:microchip technology 系列:Hyper Speed Control?，SuperSwitcher II? 包装:剪切带（CT） 零件状态:过期 功能:降压 输出配置:正 拓扑:降压 输出类型:可调式 输出数:1 电压 - 输入（最小值）:30V 电压 - 输入（最大值）:75V 电压 - 输出（最小值/固定）:0.8V 电压 - 输出（最大值）:61.5V 电流 - 输出:4A 频率 - 开关:100kHz ~ 500kHz 同步整流器:是 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:28-PowerVQFN 变式，28-MLF? 供应商器件封装:28-MLF?（5x6） 标准包装:1 |
| MIC28510 12V EV | 功能描述:电源管理IC开发工具 75V/4A DC-DC Buck Regulator with HSC - Evaluation Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MIC28510 5V EV | 功能描述:电源管理IC开发工具 75V/4A DC-DC Buck Regulator with HSC - Evaluation Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。