- 您现在的位置：买卖IC网 > PDF目录13079 > MIC29510-5.0WT (Micrel Inc)IC REG LDO 5A 5V TO220-3 PDF资料下载
参数资料
| 型号： | MIC29510-5.0WT |
| 厂商： | Micrel Inc |
| 文件页数： | 7/10页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 5A 5V TO220-3 |
| 标准包装： | 50 |
| 应用： | 转换器，Intel Pentium? Plus |
| 输入电压： | 6 V ~ 8 V |
| 输出数： | 1 |
| 输出电压： | 5V |
| 工作温度： | 0°C ~ 125°C |
| 安装类型： | 通孔 |
| 封装/外壳： | TO-220-3 |
| 供应商设备封装： | TO-220-3 |
| 包装： | 管件 |
Micrel, Inc.
Applications Information
The MIC29510 and MIC29512 are high performance
low-dropout voltage regulators suitable for all moderate
to high-current voltage regulator applications. Their
600mV of dropout voltage at full load make them
especially valuable in battery powered systems and as
high efficiency noise filters in “post-regulator”
MIC29510/29512
Thermal Design
Linear regulators are simple to use. The most
complicated design parameters to consider are thermal
characteristics. Thermal design requires the following
application-specific parameters:
? Maximum ambient temperature, T A
applications. Unlike older NPN-pass transistor designs,
where the minimum dropout voltage is limited by the
base-emitter voltage drop and collector-emitter
saturation voltage, dropout performance of the PNP
?
?
?
Output Current, I OUT
Output Voltage, V OUT
Input Voltage, V IN
output of these devices is limited merely by the low VCE
saturation voltage.
A trade-off for the low dropout voltage is a varying base
drive requirement. But Micrel’s Super ?eta PNP?
process reduces this drive requirement to merely 2 to
5% of the load current.
MIC29510/512 regulators are fully protected from
damage due to fault conditions. Current limiting is
First, we calculate the power dissipation of the regulator
from these numbers and the device parameters from this
datasheet.
P D = I OUT × (1.02V IN – V OUT )
Where the ground current is approximated by 3% of I OUT ,
then the heat sink thermal resistance is determined with
this formula:
provided. This limiting is linear; output current under
overload conditions is constant. Thermal shutdown
disables the device when the die temperature exceeds
the maximum safe operating temperature.
θ SA =
T J(MAX) ? T A
P D
? ( θ JC + θ CS )
Transient protection allows device (and load) survival
even when the input voltage spike above and below
nominal. The output structure of these regulators allows
voltages in excess of the desired output voltage to be
applied without reverse current flow. The MIC29512
version offers a logic level ON/OFF control: when
disabled, the devices draw nearly zero current.
An additional feature of this regulator family is a common
pinout: a design’s current requirement may change up or
down yet use the same board layout, as all of Micrel’s
high-current Super ?eta PNP? regulators have identical
pinouts.
Figure 3. The MIC29510 requires only
two capacitors for operation
Where T J MAX ≤ 125°C and θ CS is between 0 and 2°C/W.
The heat sink may be significantly reduced in
applications where the minimum input voltage is known
and is large compared with the dropout voltage. Use a
series input resistor to drop excessive voltage and
distribute the heat between this resistor and the
regulator. The low dropout properties of Micrel Super
?eta PNP regulators allow very significant reductions in
regulator power dissipation and the associated heat sink
without compromising performance. When this technique
is employed, a capacitor of at least 0.1μF is needed
directly between the input and regulator ground.
Please refer to Application Note 9 for further details and
examples on thermal design and heat sink specification.
Capacitor Requirements
For stability and minimum output noise, a capacitor on
the regulator output is necessary. The value of this
capacitor is dependent upon the output current; lower
currents allow smaller capacitors. MIC29510/2
regulators are stable with a minimum capacitor value of
47μF at full load.
This capacitor need not be an expensive low ESR type:
aluminum electrolytics are adequate. In fact, extremely
low ESR capacitors may contribute to instability.
Tantalum capacitors are recommended for systems
where fast load transient response is important.
May 2006
7
M9999-051706
(408) 955-1690
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J5K-EZ-B1 | CONVERTER MOD DC/DC 40V 25W |
| LTC3831EGN#TRPBF | IC SW REG CONTROLLR SYNC 16-SSOP |
| HBC31DRXH-S734 | CONN EDGECARD 62POS DIP .100 SLD |
| LTC1262IS8#TR | IC CONV DC/DC FLASH MEMORY 8SOIC |
| EMC28DRES-S734 | CONN EDGECARD 56POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC29512BT | 功能描述:IC REG LDO USB 5A ADJ TO220-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| MIC29512WT | 功能描述:低压差稳压器 - LDO 5.0A LDO Adj. + Shutdown (RoHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC2951-3.3BM | 功能描述:IC REG LDO 3.3V/ADJ .15A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC2951-3.3BM TR | 功能描述:IC REG LDO 3.3V/ADJ .15A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC2951-3.3BMM | 功能描述:IC REG LDO 3.3V/ADJ .15A 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
发布紧急采购，3分钟左右您将得到回复。