参数资料
| 型号： | MIC3002GML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 39/65页 |
| 文件大小： | 0K |
| 描述： | IC LASER DRIVR 10GBPS 3.6V 24MLF |
| 标准包装： | 1,000 |
| 类型： | 激光二极管控制器（光纤） |
| 数据速率： | 10Gbps |
| 通道数： | 1 |
| 电源电压： | 3 V ~ 3.6 V |
| 电流 - 电源： | 2.3mA |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 24-VFQFN 裸露焊盘，24-MLF? |
| 供应商设备封装： | 24-MLF?（4x4） |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页
Micrel, Inc.
Figure 24. Four-Byte Page White Protocol
MIC3002
Acknowledge Polling
The MIC3002’s non-volatile memory cannot be accessed
during the internal write process. To allow for maximum
speed bulk writes, the MIC3002 supports acknowledge
polling. The MIC3002 will not acknowledge serial bus
transactions while internal writes are in progress. The host
may therefore monitor for the end of the write process by
periodically checking for an acknowledgement.
Write Protection and Data Security
OEM Password
A password is required to access the OEM areas of the
MIC3002, specifically the non-volatile memory, look-up
tables, and registers at serial addresses A4 h and A6 h . A four-
byte field, OEMPWSET, at serial address A6 h is used for
setting the OEM password. The OEM password is set by
writing OEMPWSET with the new value. The password
comparison is performed following the write to the MSB of
the OEMPW, address 7B h (or 7E h ) at serial address A2 h .
Therefore, this byte must be written last. A four-byte burst-
write sequence to address 78 h (or 7B h ) may be used as this
will result in the MSB being written last. The new password
will not take effect until after a power-on reset occurs or a
warm reset is performed using the RST bit in OEMCFG0.
This allows the new password to be verified before it takes
effect.
The corresponding four-byte field for password entry,
OEMPW, is located at serial address A2 h . This field is
therefore always visible to the host system. OEMPW is
compared to the four-byte OEMPWSET field at serial
address A6 h . If the two fields match, access is allowed to the
OEM areas of the MIC3002 non-volatile memory at serial
addresses A4 h and A6 h . If OEMPWSET is all zeroes, no
password security will exist. The value in OEMPW will be
ignored. This helps prevent a deliberately unsecured
MIC3002 from being inadvertently locked. Once a valid
password is entered, the MIC3002 OEM areas will be
accessible. The OEM areas may be re-secured by writing an
incorrect password value at OEMPW, e.g., all zeroes. In all
cases, OEMPW must be written LSB first through MSB last.
The OEM areas will be inaccessible following the final write
operation to OEMPW’s LSB. The OEMPW field is reset to all
zeros at power on. Any values written to these locations will be
readable by the host regardless of the locked/unlocked status
of the device. If OEMPWSET is set to zero (00000000 h ), the
MIC3002 will remain unlocked regardless of the contents of the
OEMPW field. This is the factory default security setting.
Note that a valid OEM password allows access to the OEM
and user areas of the chip, i.e., the entire memory map,
regardless of any user password that may be in place. Once
the OEM areas are locked, the user password can provide
access and write protection for the user areas.
User Password
A password is required to access the USER areas of the
MIC3002, specifically, the non-volatile memory at serial
addresses A0 h and A2 h . A one-byte field, USRPWSET at serial
address A2 h is used for setting the USER password.
USRPWSET is compared to the USRPW field at serial address
A2 h . If the two fields match, access is allowed to the USER
areas of the MIC3002 non-volatile memory at serial addresses
A0 h and A2 h . The USER password is set by writing
USRPWSET with the new value. The new password will not
take effect until after a power-on reset occurs or a warm reset
is performed using the RST bit in OEMCFG0. This allows the
new password to be verified before it takes effect.
Note also that a valid OEM password allows access to the
OEM and user areas of the chip, i.e., the entire memory map,
regardless of any user password that may be in place. Once
the OEM areas are locked, the user password can then provide
access and write protection for the user areas. If a valid OEM
password is in place, the user password will have no effect.
July 2007
39
M9999-073107-B
hbwhelp@micrel.com or (408) 955-1690
相关PDF资料 |
PDF描述 |
|---|---|
| MIC3003GFL TR | IC FOM MANAGEMENT W/CALIBR 24MLF |
| MIC3003GML TR | IC FOM MANAGEMENT W/CALIBR 24MLF |
| MIC3172BN | IC REG BUCK BOOST INV CUK 8DIP |
| MIC33030-AYHJ TR | IC REG BUCK ADJ 0.4A 10HMLF |
| MIC33050-CYHL TR | IC REG BUCK SYNC 1V 0.6A 12MLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC3003 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibration |
| MIC3003_11 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:FOM Management IC with Internal Calibration |
| MIC3003AGML | 功能描述:网络控制器与处理器 IC FOM Controller with Internal Calibration RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MIC3003AGML TR | 功能描述:网络控制器与处理器 IC FOM Controller with Internal Calibration RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MIC3003GFL | 功能描述:网络控制器与处理器 IC FOM Controller with Internal Calibration in Ultra Small Package RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。