- 您现在的位置：买卖IC网 > PDF目录14541 > MIC33050-GYHL TR (Micrel Inc)IC REG BUCK SYNC 1.8V 0.6A 12MLF PDF资料下载
参数资料
| 型号： | MIC33050-GYHL TR |
| 厂商： | Micrel Inc |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC 1.8V 0.6A 12MLF |
| 产品培训模块： | MIC23xxx HyperLight Load™ Regulators |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 1.8V |
| 输入电压： | 2.7 V ~ 5.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 4MHz |
| 电流 - 输出： | 600mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-VFDFN 裸露焊盘，12-MLF? |
| 包装： | 标准包装 |
| 供应商设备封装： | 12-MLF?（3x3） |
| 产品目录页面： | 1094 (CN2011-ZH PDF) |
| 其它名称： | 576-3040-6 |
Micrel, Inc.
Applications Information
MIC33050
Input Capacitor
A minimum of 2.2μF ceramic capacitor should be placed
close to the VIN pin and PGND pin for bypassing. X5R or
X7R dielectrics are recommended for the input capacitor.
Y5V dielectrics, aside from losing most of their
capacitance over temperature, they also become resistive
at high frequencies. This reduces their ability to filter out
100
90
80
Efficiency V OUT = 1.8V
V IN = 3.0V
70 V
high frequency noise.
Output Capacitor
60
IN
= 3.6V
V IN = 4.2V
The MIC33050 was designed for use with a 2.2μF or
1
greater ceramic output capacitor. A low equivalent series
resistance (ESR) ceramic output capacitor either X7R or
X5R is recommended. Y5V and Z5U dielectric capacitors,
aside from the undesirable effect of their wide variation in
50
10 100 1000
OUTPUT CURRENT (mA)
? ? ? 100
Efficiency (%) ? ? ? OUT
capacitance over temperature, become resistive at high
frequencies.
Compensation
The MIC33050 is designed to be stable with an internal
inductor with a minimum of 2.2μF ceramic (X5R) output
capacitor.
Efficiency Considerations
Efficiency is defined as the amount of useful output power,
divided by the amount of power supplied.
? V ? I OUT ?
? V IN ? I IN ?
Maintaining high efficiency serves two purposes. It
reduces power dissipation in the power supply, reducing
the need for heat sinks and thermal design considerations
and it reduces consumption of current for battery powered
applications. Reduced current draw from a battery
increases the devices operating time and is critical in hand
held devices.
The Figure above shows an efficiency curve. From 1μA to
100mA, efficiency losses are dominated by quiescent
current losses, gate drive and transition losses. By using
the HyperLight Load ? mode, the MIC33050 is able to
maintain high efficiency at low output currents.
Over 100mA, efficiency loss is dominated by MOSFET
RDSON and inductor losses. Higher input supply voltages
will increase the Gate-to-Source threshold on the internal
MOSFETs, thereby reducing the internal RDSON. This
improves efficiency by reducing DC losses in the device.
All but the inductor losses are inherent to the device. In
which case, inductor selection becomes increasingly
critical in efficiency calculations. As the inductors are
reduced in size, the DC resistance (DCR) can become
quite significant. The DCR losses can be calculated as
follows:
L PD = I OUT2 × DCR
From that, the loss in efficiency due to inductor resistance
can be calculated as follows;
V OUT ? I OUT
Efficiency Loss (%) ? ? 1 ? ? ?
? ? ? ? 100
There are two types of losses in switching converters; DC
losses and switching losses. DC losses are simply the
power dissipation of I 2 R. Power is dissipated in the high
side switch during the on cycle. Power loss is equal to the
? ?
?
? ? V OUT ? I OUT ? L PD
? ?
? ? ?
high side MOSFET R DSON multiplied by the square of the
Switch Current. During the off cycle, the low side N-
channel MOSFET conducts, also dissipating power.
Device operating current also reduces efficiency. The
product of the quiescent (operating) current and the supply
voltage is another DC loss. The current required driving
the gates on and off at a constant 4MHz frequency and the
switching transitions make up the switching losses.
Efficiency loss due to DCR is minimal at light loads and
gains significance as the load is increased. Inductor
selection becomes a trade-off between efficiency and size
in this case.
May 2012
10
M9999-050312-C
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J0B-EX-S | CONVERTER MOD DC/DC 95V 75W |
| VI-J04-EX-S | CONVERTER MOD DC/DC 48V 75W |
| MIC23250-AAYMT TR | IC REG BUCK SYNC ADJ 0.4A 12TMLF |
| VI-B1Z-EV-S | CONVERTER MOD DC/DC 2V 60W |
| VI-2VR-EX-S | CONVERTER MOD DC/DC 7.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC33050-SYHL | 制造商:Micrel 功能描述:4MHz PWM Buck Regulator |
| MIC33050-SYHL TR | 功能描述:直流/直流开关调节器 High Efficiency 600mA Inductor-less Buck Regulator featuring Hyper Light Load RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC33050-SYHL-EV | 功能描述:MIC33050 HyperLight Load? DC/DC, Step Down 1, Non-Isolated Outputs Evaluation Board 制造商:microchip technology 系列:HyperLight Load? 零件状态:有效 主要用途:DC/DC，步降 输出和类型:1，非隔离 功率 - 输出:- 电压 - 输出:3.3V 电流 - 输出:600mA 电压 - 输入:2.7 V ~ 5.5 V 稳压器拓扑:降压 频率 - 开关:4MHz 板类型:完全填充 所含物品:板 使用的 IC/零件:MIC33050 标准包装:1 |
| MIC33050-SYHL-TR | 功能描述:Buck Switching Regulator IC Positive Fixed 3.3V 1 Output 600mA 12-VFDFN Exposed Pad, 12-MLF? 制造商:microchip technology 系列:HyperLight Load? 包装:剪切带（CT） 零件状态:停产 功能:降压 输出配置:正 拓扑:降压 输出类型:固定 输出数:1 电压 - 输入（最小值）:2.7V 电压 - 输入（最大值）:5.5V 电压 - 输出（最小值/固定）:3.3V 电压 - 输出（最大值）:- 电流 - 输出:600mA 频率 - 开关:4MHz 同步整流器:是 工作温度:-40°C ~ 125°C （TJ） 安装类型:表面贴装 封装/外壳:12-VFDFN 裸焊盘，12-MLF? 供应商器件封装:12-MLF?（3x3） 标准包装:1 |
| MIC-3312 | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:6U CompactPCI? Extension Board for MIC-3393 |
发布紧急采购，3分钟左右您将得到回复。