- 您现在的位置：买卖IC网 > PDF目录299479 > MIC37102BMTR (MICREL INC) 1.24 V-6 V ADJUSTABLE POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PDSO8 PDF资料下载
参数资料
| 型号： | MIC37102BMTR |
| 厂商： | MICREL INC |
| 元件分类： | 可调正电压单路输出LDO稳压器 |
| 英文描述： | 1.24 V-6 V ADJUSTABLE POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PDSO8 |
| 封装： | SOIC-8 |
| 文件页数： | 9/11页 |
| 文件大小： | 477K |
| 代理商： | MIC37102BMTR |
Voltage Transformation Module
VT048A015T100FP
vicorpower.com
Rev. 1.1
Page 7 of 11
APPLICATION NOTES & TEST CIRCUIT
Parallel Operation
In applications requiring higher current or redundancy, VTMs can be
operated in parallel without adding control circuitry or signal lines. To
maximize current sharing accuracy, it is imperative that the source and
load impedance on each VTM in a parallel array be equal. If VTMs are
being fed by an upstream PRM, the VC nodes of all VTMs must be con-
nected to the PRM VC.
To achieve matched impedances, dedicated power planes within the PC
board should be used for the output and output return paths to the
array of paralleled VTMs. This technique is preferable to using traces of
varying size and length.
The VTM power train and control architecture allow bi-directional power
transfer when the VTM is operating within its specified ranges. Bi-direc-
tional power processing improves transient response in the event of an
output load dump. The VTM may operate in reverse, returning output
power back to the input source. It does so efficiently.
Input Impedance Recommendations
To take full advantage of the VTM’s capabilities, the impedance of the
source (input source plus the PC board impedance) must be low over a
range from DC to 5 MHz. The input of the VTM (factorized bus) should
be locally bypassed with a 8 F low Q aluminum electrolytic capacitor.
Additional input capacitance may be added to improve transient
performance or compensate for high source impedance. The VTM has
extremely wide bandwidth so the source response to transients is usually
the limiting factor in overall output response of the VTM.
Anomalies in the response of the source will appear at the output of the
VTM, multiplied by its K factor of 1/32. The DC resistance of the source
should be kept as low as possible to minimize voltage deviations on the
input to the VTM. If the VTM is going to be operating close to the high
limit of its input range, make sure input voltage deviations will not trig-
ger the input overvoltage turn-off threshold.
Input Fuse Recommendations
VI BRICKs are not internally fused in order to provide flexibility in config-
uring power systems. However, input line fusing of VI BRICKs must
always be incorporated within the power system. A fast acting fuse is
required to meet safety agency Conditions of Acceptability. The input
line fuse should be placed in series with the +In port. For agency
approvals and fusing conditions, click on the link below:
Application Notes
For VTM and VI BRICK application notes on soldering, board layout, and
system design please click on the link below:
Applications Assistance
Please contact Vicor Applications Engineering for assistance,
1-800-927-9474, or email at apps@vicorpower.com.
F1
Load
+
–
Input reflected ripple
measurement point
C2
0.47
μF
ceramic
+
–
14 V
VTM
+IN
+OUT
-OUT
+OUT
-OUT
-IN
TM
VC
PC
Figure 10 — VI BRICK VTM test circuit
Notes:
1. C3 should be placed close to the load
2. R3 may be ESR of C3 or a separate damping resistor.
[a] See Input Fuse Recommendations section
C3
94 F
R3
5m
Ω
C1
47 F
Al electrolytic
7A[a]
Fuse
相关PDF资料 |
PDF描述 |
|---|---|
| MIC3775-3.0BMMTR | 3 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PDSO8 |
| MIC3775-1.65BMMTR | 1.65 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PDSO8 |
| MIC3808YMTR | 1 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| MIC39100-5.0BSTR | 5 V FIXED POSITIVE LDO REGULATOR, 0.63 V DROPOUT, PDSO4 |
| MIC3975-1.8YMMTR | 1.8 V FIXED POSITIVE LDO REGULATOR, 0.5 V DROPOUT, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC37102BR | 功能描述:IC REG LDO ADJ 1A SPAK-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC37102BR TR | 功能描述:IC REG LDO ADJ 1A SPAK-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC37102WR | 功能描述:低压差稳压器 - LDO 1.0A Low Voltage ADJ. uCap LDO Regulator in 5 Lead SPAK(ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC37102WR TR | 功能描述:低压差稳压器 - LDO 1.0A Low Voltage ADJ. uCap LDO Regulator in 5 Lead SPAK(ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC37102WRTR | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: 制造商:Micrel Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。