- 您现在的位置：买卖IC网 > PDF目录19732 > MIC37102BR (Micrel Inc)IC REG LDO ADJ 1A SPAK-5 PDF资料下载
参数资料
| 型号： | MIC37102BR |
| 厂商： | Micrel Inc |
| 文件页数： | 13/15页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ 1A SPAK-5 |
| 标准包装： | 48 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 1.24 V ~ 6 V |
| 输入电压： | 2.25 V ~ 6 V |
| 电压 - 压降（标准）： | 0.28V @ 1A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1A（最小） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SPAK-5 |
| 供应商设备封装： | S-PAK-5 |
| 包装： | 管件 |
Micrel, Inc.
Figure 4 shows copper area versus power dissipation
with each trace corresponding to a different temperature
rise above ambient.
From these curves, the minimum area of copper
necessary for the part to operate safely can be
determined. The maximum allowable temperature rise
must be calculated to determine operation along which
curve.
? T = T J(max) – T A(max)
T J(max) = 125°C
T A(max) = maximum ambient operating temp-
erature.
For example, the maximum ambient temperature is
50°C, the ? T is determined as follows:
MIC37100/37101/37102
Quick Method
Determine the power dissipation requirements for the
design along with the maximum ambient temperature at
which the device will be operated. Refer to Figure 5,
which shows safe operating curves for three different
ambient temperatures: 25°C, 50°C and 85°C. From
these curves, the minimum amount of copper can be
determined by knowing the maximum power dissipation
required. If the maximum ambient temperature is 50°C
and the power dissipation is as above, 836mW, the
curve in Figure 5 shows that the required area of copper
is 160mm 2 .
The θ JA of this package is ideally 63°C/W, but it will vary
depending upon the availability of copper ground plane
to which it is attached.
J
? T = 125°C – 50°C
? T = 75°C
Using Figure 4, the minimum amount of required copper
can be determined based on the required power
dissipation. Power dissipation in a linear regulator is
calculated as follows:
P D = (V IN – V OUT ) I OUT + V IN × I GND
If we use a 2.5V output device and a 3.3V input at an
output current of 1A, then our power dissipation is as
900
800
700
600
500
400
300
200
100
T = 125°C
T A = 85°C
50°C 25°C
follows:
0
0
0.25 0.50 0.75 1.00 1.25 1.50
P D = (3.3V – 2.5V) × 1A + 3.3V × 11mA
P D = 800mW + 36mW
P D = 836mW
From Figure 4, the minimum amount of copper required
to operate this application at a ? T of 75°C is 160mm 2 .
POWER DISSIPATION (W)
Figure 5. Copper Area vs. Power-SOIC
Power Dissipation
September 2007
13
M9999-090607
相关PDF资料 |
PDF描述 |
|---|---|
| MIC37102BM TR | IC REG LDO ADJ 1A 8-SOIC |
| MIC2585-2JBTS | IC CTRLR HOT SWAP DUAL 24-TSSOP |
| TOP243GN | IC OFFLINE SWIT OVP UVLO HV 8SMD |
| MIC37102BM | IC REG LDO ADJ 1A 8-SOIC |
| MIC2585-1MBTS TR | IC CTRLR HOT SWAP DUAL 24-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC37102BR TR | 功能描述:IC REG LDO ADJ 1A SPAK-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC37102WR | 功能描述:低压差稳压器 - LDO 1.0A Low Voltage ADJ. uCap LDO Regulator in 5 Lead SPAK(ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC37102WR TR | 功能描述:低压差稳压器 - LDO 1.0A Low Voltage ADJ. uCap LDO Regulator in 5 Lead SPAK(ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC37102WRTR | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: 制造商:Micrel Inc 功能描述: |
| MIC37102YM | 功能描述:低压差稳压器 - LDO LV, 1.0A Cap Adj. Vout LDO in SO-8 (Lead Free) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。