- 您现在的位置：买卖IC网 > PDF目录19723 > MIC37252BU (Micrel Inc)IC REG LDO ADJ 2.5A TO-263 PDF资料下载
参数资料
| 型号： | MIC37252BU |
| 厂商： | Micrel Inc |
| 文件页数： | 7/8页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ 2.5A TO-263 |
| 标准包装： | 50 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 1.24 V ~ 5.5 V |
| 输入电压： | 3 V ~ 6 V |
| 电压 - 压降（标准）： | 0.55V @ 2.5A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 2.5A（最小） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-6，D²Pak（5 引线+接片），TO-263BA |
| 供应商设备封装： | TO-263-5 |
| 包装： | 管件 |
R1 = R2 ? ? OUT ? 1 ? ?
Micrel, Inc.
Transient Response and 5V to 3.3V or 3.3V to
1.8VConversions
The MIC37252 has excellent transient response to
variations in input voltage and load current. The device
has been designed to respond quickly to load current
variations and input voltage variations. Large output
capacitors are not required to obtain this performance.
A standard 10μF output capacitor, preferably tantalum,
is all that is required. Larger values help to improve
performance even further.
By virtue of its low dropout voltage, this device does not
saturate into dropout as readily as similar NPN-based
designs. When converting from 3.3V to 1.8V, the NPN-
based regulators are already operating in dropout, with
typical dropout requirements of 2V or greater. To convert
down to1.8V without operating in dropout, NPN-based
regulators require an input voltage of 3.8V at the very
least. The MIC37252 regulator will provide excellent
performance with an input as low as 3.0V. This gives the
PNP-based regulators a distinct advantage over older
NPN-based linear regulators.
Minimum Load Current
The MIC37252 regulator is specified between finite
loads. If the output current is too small, leakage currents
dominate and the output voltage rises. A 10mA minimum
load current is necessary for proper operation.
Enable Input
The MIC37252 also features an enable input for on/off
control of the device. Its shutdown state draws “zero”
current (only microamperes of leakage). The enable
MIC37252
input is TTL/CMOS compatible for simple logic interface,
but can be connected to up to VIN. When enabled, it
draws approximately 15μA.
Adjustable Regulator Design
Figure 2. Adjustable Regulator with Resistors
The MIC37252 allows programming of the output voltage
anywhere between 1.24V and the 5.5V maximum
operating rating of the family. Two resistors are used.
Resistors values are recommended to be less than 10k ?
in value to improve stability. The resistor values can be
sized to draw the mini-mum load current for this device.
The resistor values are calculated by:
? V ?
? 1.240 ?
Where V OUT is the desired output voltage. Figure 2
shows component definition. Applications with widely
varying load currents may scale the resistors to draw the
minimum load current required for proper operation (see
above).
February 2006
7
M9999-021606
(408) 955-1690
相关PDF资料 |
PDF描述 |
|---|---|
| 171-009-203L001 | CONN DB9 FEMALE SLD CUP NICKEL |
| LC5512MB-75F256C | IC XPLD 512MC 7.5NS 256FPBGA |
| ISPLSI 1048E-70LTN | IC PLD ISP 96I/O 15NS 128TQFP |
| EBC05DRYH | CONN EDGECARD 10POS DIP .100 SLD |
| LLM215R70J224MA11L | CAP CER 0.22UF 6.3V 20% X7R 0805 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC37252BU TR | 功能描述:IC REG LDO ADJ 2.5A TO-263 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC37252WR | 功能描述:低压差稳压器 - LDO LV, 2.5A Cap LDO in Spak (ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC37252WR TR | 功能描述:低压差稳压器 - LDO LV, 2.5A Cap LDO in Spak (ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC37252WRTR | 制造商:Micrel Inc 功能描述: |
| MIC37252WU | 功能描述:低压差稳压器 - LDO LV, 2.5A Cap LDO in TO-263 (ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。