参数资料
| 型号： | MIC37252WU TR |
| 厂商： | Micrel Inc |
| 文件页数： | 7/8页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ 2.5A TO-263 |
| 标准包装： | 750 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 1.24 V ~ 5.5 V |
| 输入电压： | 3 V ~ 6 V |
| 电压 - 压降（标准）： | 0.55V @ 2.5A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 2.5A（最小） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-6，D²Pak（5 引线+接片），TO-263BA |
| 供应商设备封装： | TO-263-5 |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC37252WUTR MIC37252WUTR-ND |
R1 = R2 ? ? OUT ? 1 ? ?
Micrel, Inc.
Transient Response and 5V to 3.3V or 3.3V to
1.8VConversions
The MIC37252 has excellent transient response to
variations in input voltage and load current. The device
has been designed to respond quickly to load current
variations and input voltage variations. Large output
capacitors are not required to obtain this performance.
A standard 10μF output capacitor, preferably tantalum,
is all that is required. Larger values help to improve
performance even further.
By virtue of its low dropout voltage, this device does not
saturate into dropout as readily as similar NPN-based
designs. When converting from 3.3V to 1.8V, the NPN-
based regulators are already operating in dropout, with
typical dropout requirements of 2V or greater. To convert
down to1.8V without operating in dropout, NPN-based
regulators require an input voltage of 3.8V at the very
least. The MIC37252 regulator will provide excellent
performance with an input as low as 3.0V. This gives the
PNP-based regulators a distinct advantage over older
NPN-based linear regulators.
Minimum Load Current
The MIC37252 regulator is specified between finite
loads. If the output current is too small, leakage currents
dominate and the output voltage rises. A 10mA minimum
load current is necessary for proper operation.
Enable Input
The MIC37252 also features an enable input for on/off
control of the device. Its shutdown state draws “zero”
current (only microamperes of leakage). The enable
MIC37252
input is TTL/CMOS compatible for simple logic interface,
but can be connected to up to VIN. When enabled, it
draws approximately 15μA.
Adjustable Regulator Design
Figure 2. Adjustable Regulator with Resistors
The MIC37252 allows programming of the output voltage
anywhere between 1.24V and the 5.5V maximum
operating rating of the family. Two resistors are used.
Resistors values are recommended to be less than 10k ?
in value to improve stability. The resistor values can be
sized to draw the mini-mum load current for this device.
The resistor values are calculated by:
? V ?
? 1.240 ?
Where V OUT is the desired output voltage. Figure 2
shows component definition. Applications with widely
varying load currents may scale the resistors to draw the
minimum load current required for proper operation (see
above).
February 2006
7
M9999-021606
(408) 955-1690
相关PDF资料 |
PDF描述 |
|---|---|
| MIC37252WR TR | IC REG LDO ADJ 2.5A S-PAK-5 |
| MIC39150-1.65WT | IC REG LDO 1.65V 1.5A TO220 |
| RGM28DTMN-S189 | CONN EDGECARD 56POS R/A .156 SLD |
| RMM28DTMN-S189 | CONN EDGECARD 56POS R/A .156 SLD |
| RSA30DRMI-S288 | CONN EDGECARD 60POS .125 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC37300 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:3.0A, LOW VOLTAGE UCAP LDO REGULATOR |
| MIC37300_09 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:3.0A, Low-Voltage μCap LDO Regulator |
| MIC37300-1.5BR | 功能描述:IC REG LDO 1.5V 3A S-PAK-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC37300-1.5BR TR | 功能描述:IC REG LDO 1.5V 3A S-PAK-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC37300-1.5WR | 功能描述:低压差稳压器 - LDO 3A Low Voltage LDO Regulator(ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。