- 您现在的位置：买卖IC网 > PDF目录19721 > MIC37501-1.8BR TR (Micrel Inc)IC REG LDO 1.8V SPAK-7 PDF资料下载
参数资料
| 型号： | MIC37501-1.8BR TR |
| 厂商： | Micrel Inc |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.8V SPAK-7 |
| 标准包装： | 750 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.8V |
| 输入电压： | 2.3 V ~ 6 V |
| 电压 - 压降（标准）： | 0.33V @ 5A |
| 稳压器数量： | 1 |
| 电流 - 限制（最小）： | 5A |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SPak（7 引线 + 接片） |
| 供应商设备封装： | S-PAK-7 |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC37501-1.8BRTR MIC37501-1.8BRTR-ND |
Micrel, Inc.
Application Information
The MIC37501/02 is a high-performance, low dropout
voltage regulator suitable for moderate to high-current
regulator applications. Its 500mV dropout voltage at
full load makes it especially valuable in battery-
powered systems and as a high-efficiency noise filter
in post-regulator applications. Unlike older NPN-pass
transistor designs, where the minimum dropout
voltage is limited by the based-to-emitter voltage drop
and collector-to-emitter saturation voltage, dropout
performance of the PNP output of these devices is
limited only by the low V CE saturation voltage.
A trade-off for the low dropout voltage is a varying
base drive requirement. Micrel’s Super β eta PNP ?
process reduces this drive requirement to only 2% to
5% of the load current.
The MIC37501/02 regulator is fully protected from
damage due to fault conditions. Current limiting is
provided. This limiting is linear; output current during
overload conditions is constant. Thermal shutdown
disables the device when the die temperature
exceeds the maximum safe operating temperature.
The output structure of these regulators allows
voltages in excess of the desired output voltage to be
applied without reverse current flow.
Thermal Design
Linear regulators are simple to use. The most
complicated design parameters to consider are
thermal characteristics. Thermal design requires the
following application-specific parameters:
? Maximum ambient temperature (T A )
? Output current (I OUT )
? Output voltage (V OUT )
? Input voltage (V IN )
? Ground current (I GND )
First, calculate the power dissipation of the regulator
from these numbers and the device parameters from
this data sheet.
P D = (V IN – V OUT ) I OUT + V IN I GND
where the ground current is approximated by using
numbers from the “Electrical Characteristics” or
“Typical Characteristics” sections. The heat sink
thermal resistance is then determined with this
formula:
θ SA = ((T J (max) – T A )/ P D ) – ( θ JC + θ CS )
Where T J (max) ≤ ? 125 ° C and θ CS is between 0 ° C and
2 ° C/W. The heat sink may be significantly reduced in
applications where the minimum input voltage is
known and is large compared with the dropout
voltage. Use a series input resistor to drop excessive
voltage and distribute the heat between this resistor
MIC37501/37502
and the regulator. The low dropout properties of Micrel
Super β eta PNP ? regulators allow significant
reductions in regulator power dissipation and the
associated heat sink without compromising
performance. When this technique is employed, a
capacitor of at least 1.0μF is needed directly between
the input and regulator ground.
Refer to “Application Note 9” for further details and
examples on thermal design and heat sink
applications.
Output Capacitor
The MIC37501/02 requires an output capacitor for
stable operation. As a μCap LDO, the MIC37501/02
can operate with ceramic output capacitors as long as
the amount of capacitance is 100μF or greater. For
values of output capacitance lower than 100μF, the
recommended ESR range is 200m ? to 2 ? . The
minimum value of output capacitance recommended
for the MIC37501/02 is 47μF.
For 100μF or greater, the ESR range recommended is
less than 1 ? . Ultra-low ESR ceramic capacitors are
recommended for output capacitance of 100μF or
greater to help improve transient response and noise
reduction at high frequency. X7R/X5R dielectric-type
ceramic capacitors are recommended because of
their temperature performance. X7Rtype capacitors
change capacitance by 15% over their operating
temperature range and are the most stable type of
ceramic capacitors. Z5U and Y5V dielectric capacitors
change value by as much as 50% and 60%,
respectively, over their operating temperature ranges.
To use a ceramic chip capacitor with Y5V dielectric,
the value must be much higher than an X7R ceramic
capacitor to ensure the same minimum capacitance
over the equivalent operating temperature range.
Input Capacitor
An input capacitor of 1.0μF or greater is recom-
mended when the device is more than 4 inches away
from the bulk supply capacitance, or when the supply
is a battery. Small, surfacemount chip capacitors can
be used for the bypassing. The capacitor should be
placed within 1" of the device for optimal performance.
Larger values will help to improve ripple rejection by
bypassing the input to the regulator, further improving
the integrity of the output voltage.
Transient Response and 3.3V to 2.5V, 2.5V to 1.8V
or 1.65V, or 2.5V to 1.5V Conversions
The MIC37501/02 has excellent transient response to
variations in input voltage and load current. The
device has been designed to respond quickly to load
current variations and input voltage variations. Large
output capacitors are not required to obtain this
performance. A standard 47μF output capacitor is all
May 2011
8
M9999-050511-B
相关PDF资料 |
PDF描述 |
|---|---|
| GRM32RR71C475MC01L | CAP CER 4.7UF 16V 20% X7R 1210 |
| M4A3-256/128-7SAC | IC CPLD ISP 4A 256MC 256SBGA |
| MIC37501-1.8BR | IC REG LDO 1.8V SPAK-7 |
| LC4256V-75FTN256BI | IC CPLD 256MACROCELLS 256FTBGA |
| MIC3775-3.0BMM TR | IC REG LDO 3V .75A 8-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC37501-2.5BR | 功能描述:IC REG LDO 2.5V SPAK-7 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC37501-2.5BR TR | 功能描述:IC REG LDO 2.5V SPAK-7 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC37501-2.5WR | 功能描述:低压差稳压器 - LDO 5A Low Voltage LDO Regulator(ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC37501-2.5WR TR | 功能描述:低压差稳压器 - LDO 5A Low Voltage LDO Regulator(ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC37501-3.3BR | 功能描述:IC REG LDO 3.3V SPAK-7 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
发布紧急采购，3分钟左右您将得到回复。