参数资料
| 型号： | MIC37502WU TR |
| 厂商： | Micrel Inc |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ TO-263-5 |
| 标准包装： | 750 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 1.24 V ~ 5.5 V |
| 输入电压： | 2.3 V ~ 6 V |
| 电压 - 压降（标准）： | 0.33V @ 5A |
| 稳压器数量： | 1 |
| 电流 - 限制（最小）： | 5A |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-6，D²Pak（5 引线+接片），TO-263BA |
| 供应商设备封装： | TO-263-5 |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC37502WUTR MIC37502WUTR-ND |
Micrel, Inc.
that is required. Larger values help to improve
performance even further.
By virtue of its low dropout voltage, this device does
not saturate into dropout as readily as similar NPN-
based designs. When converting from 3.3V to 2.5V,
2.5V to 1.8V or 1.65V, or 2.5V to 1.5V, the NPN-
based regulators are already operating in dropout,
with typical dropout requirements of 1.2V or greater.
To convert down to 2.5V without operating in dropout,
NPN-based regulators require an input voltage of at
least 3.7V. The MIC37501/02 regulator will provide
excellent performance with an input as low as 3.0V or
MIC37501/37502
Enable Input
The MIC37501/02 also features an enable input for
on/off control of the device. Its shutdown state draws
“zero” current (only microamperes of leakage). The
enable input is TTL/CMOS-compatible for simple logic
interface, but can be connected up to V IN . When
enabled, it draws approximately 15μA.
Adjustable Regulator Design
MIC37502
2.25V, respectively. This gives the PNP-based
regulators a distinct advantage over older, NPN-based
linear regulators.
Minimum Load Current
ENABLE
SHUTDOWN
V IN
IN
EN
OUT
ADJ
GND
R1
R2
V OUT
C OUT
V OUT = 1.240V ? 1 +
?
The MIC37501/02 regulator is specified between finite
loads. If the output current is too small, leakage
currents dominate and the output voltage rises. A
10mA minimum load current is necessary for proper
?
?
R1 ?
R2 ?
R1 = R2 ? ? OUT ? 1 ? ?
operation.
Error Flag
The MIC37501 features an error flag circuit that
monitors the output voltage and signals an error
condition when the voltage drops 5% below the
nominal output voltage. The error flag is an open-
collector output that can sink 10mA during a fault
condition.
Low output voltage can be caused by a number of
problems, including an overcurrent fault (device in
current limit) or low input voltage. The flag is
inoperative during overtemperature shutdown.
Figure 2. Adjustable Regulator with Resistors
The MIC37502 allows programming the output voltage
anywhere between 1.24V and the 5.5V maximum
operating rating of the family. Two resistors are used.
Resistors can be quite large, up to 1M ? , because of
the very high input impedance and low bias current of
the sense comparator.
The resistor values are calculated by:
? V ?
? 1.240 ?
Where V OUT is the desired output voltage. Figure 2
shows component definition. Applications with widely
varying load currents may scale the resistors to draw
the minimum load current required for proper
operation (see above).
May 2011
9
M9999-050511-B
相关PDF资料 |
PDF描述 |
|---|---|
| HBM36DSEF-S243 | CONN EDGECARD 72POS .156 EYELET |
| RMM24DSEI-S13 | CONN EDGECARD 48POS .156 EXTEND |
| LT3032IDE-15#TRPBF | IC REG LDO +-15V .15A 14DFN |
| LT3032IDE-12#TRPBF | IC REG LDO +-12V .15A 14DFN |
| LT3032IDE-5#TRPBF | IC REG LDO +-5V .15A 14DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC-3753 | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:72-ch Digital I/O CPCI Cards |
| MIC-3753R | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:72-ch Digital I/O CPCI Cards |
| MIC-3756 | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:72-ch Digital I/O CPCI Cards |
| MIC-3758 | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:72-ch Digital I/O CPCI Cards |
| MIC-3761 | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:8-ch Relay and Isolated Digital Input CPCI Card |
发布紧急采购，3分钟左右您将得到回复。