- 您现在的位置：买卖IC网 > Datasheet目录45 > MIC384-1YMM (Micrel Inc)IC SUPERVISR THERM LOC/REM 8MSOP Datasheet资料下载
参数资料
| 型号： | MIC384-1YMM |
| 厂商： | Micrel Inc |
| 文件页数： | 19/22页 |
| 文件大小： | 510K |
| 描述： | IC SUPERVISR THERM LOC/REM 8MSOP |
| 标准包装： | 100 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部和外部 |
| 感应温度： | -55°C ~ 125°C，外部传感器 |
| 精确度： | ±2°C 本地（最大），±3°C 远程（最大） |
| 拓扑： | ADC（三角积分型），寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 散装 |
| 产品目录页面： | 1083 (CN2011-ZH PDF) |
| 其它名称： | 576-2285 MIC384-1YMM-ND |
September 2005
19
MIC384
MIC384
Micrel
Layout Considerations
The following guidelines should be kept in mind when design-
ing and laying out circuits using the MIC384:
1. Place the MIC384 as close to the remote diodes
as possible, while taking care to avoid severe
noise sources such as high frequency power
transformers, CRTs, memory and data busses,
and the like.
2. Since any conductance from the various volt-
ages on the PC Board to the T1 or T2 line can
induce serious errors, it is good practice to guard
the remote diodes emitter traces with pairs of
ground traces. These ground traces should be
returned to the MIC384s own ground pin. They
should not be grounded at any other part of their
run. However, it is highly desirable to use these
guard traces to carry the diodes own ground
return back to the ground pin of the MIC384,
thereby providing a Kelvin connection for the
base of the diodes. See Figure 6.
3. When using the MIC384 to sense the tempera-
ture of a processor or other device which has an
integral thermal diode, e.g., Intels Pentium III,
connect the emitter and base of the remote sen-
sor to the MIC384 using the guard traces and
Kelvin return shown in Figure 6. The collector
of the remote diode is typically inaccessible to
the user on these devices. To allow for this, the
MIC384 has superb rejection of noise appearing
from collector to GND, as long as the base to
ground connection is relatively quiet.
REMOTE DIODE (T1)
GUARD/RETURN
1
2
3
DATA
CLK
/INT
GND
8
7
6
5
4
VDD
A0
T1
T2
GUARD/RETURN
REMOTE DIODE (T2)
GUARD/RETURN
GUARD/RETURN
MIC384
Figure 6. Guard Traces/Kelvin Ground Returns
4. Due to the small currents involved in the mea-
surement of the remote diodes 擵
BE
, it is
important to adequately clean the PC board after
soldering to prevent current leakage. This is
most likely to show up as an issue in situations
where water-soluble soldering uxes are used.
5. In general, wider traces for the ground and
T1/T2 lines will help reduce susceptibility to
radiated noise (wider traces are less inductive).
Use trace widths and spacing of 10 mils wher-
ever possible and provide a ground plane under
the MIC384 and under the connections from
the MIC384 to the remote diodes. This will help
guard against stray noise pickup.
6. Always place a good quality 0.1礔 power supply
bypass capacitor directly adjacent to, or under-
neath, the MIC384. Surface-mount capacitors
are preferable because of their low inductance.
7. When the MIC384 is being powered from par-
ticularly noisy power supplies, or from supplies
which may have sudden high-amplitude spikes
appearing on them, it can be helpful to add ad-
ditional power supply ltering. This should be
implemented as a 100?resistor in series with
the parts VDD pin, and an additional 4.7礔,
6.3V electrolytic capacitor from VDD to GND.
See Figure 7.
相关PDF资料 |
PDF描述 |
|---|---|
| MIC5158BN | IC REG CTRLR SGL FIX/ADJ 14-DIP |
| MIC5159BM6 TR | IC REG CTRLR SGL POS ADJ SOT23-6 |
| MIC5190BMM TR | IC REG CTRLR SGL POS ADJ 10-MSOP |
| MIC5191BMM TR | IC REG CTRLR SGL POS ADJ 10-MSOP |
| ML4800CP | IC PFC CTRLR AVERAGE CURR 16DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC384-1YMM TR | 功能描述:板上安装温度传感器 3-zone thermal supervisor; SOIC-08 - Lead Free RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MIC384-2BM | 功能描述:IC SUPERVSR THERM LOC/REM 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| MIC384-2BM TR | 功能描述:IC SUPERVSR THERM LOC/REM 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| MIC384-2BMM | 功能描述:IC SUPERVISR THERM LOC/REM 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| MIC384-2BMM TR | 功能描述:IC SUPERVISR THERM LOC/REM 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
发布紧急采购，3分钟左右您将得到回复。