- 您现在的位置：买卖IC网 > PDF目录19495 > MIC384-2YM TR (Micrel Inc)IC SUPERVSR THERM LOC/REM 8SOIC PDF资料下载
参数资料
| 型号： | MIC384-2YM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 18/22页 |
| 文件大小： | 510K |
| 描述： | IC SUPERVSR THERM LOC/REM 8SOIC |
| 标准包装： | 2,500 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部和外部 |
| 感应温度： | -55°C ~ 125°C，外部传感器 |
| 精确度： | ±2°C 本地（最大），±3°C 远程（最大） |
| 拓扑： | ADC（三角积分型），寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC384-2YMTR MIC384-2YMTR-ND |
MIC384
Micrel
MIC384
18
September 2005
Applications
Remote Diode Selection
Most small-signal PNP transistors with characteristics similar
to the JEDEC 2N3906 will perform well as remote temperature
sensors. Table 6 lists several examples of such parts that
Micrel has tested for use with the MIC384. Other transistors
equivalent to these should also work well.
Minimizing Errors
Self-Heating
One concern when using a part with the temperature accuracy
and resolution of the MIC384 is to avoid errors in measuring
the local temperature induced by self-heating. Self-heating
is caused by the power naturally dissipated inside the device
due to operating supply current and I/O sink currents (V
DD
?
I
DD
) + (V
OL
?I
OL
). In order to understand what level of error
this represents, and how to reduce that error, the dissipation
in the MIC384 must be calculated and its effects reduced to
a temperature offset.
The worst-case operating condition for the MIC384 is when
V
DD
= 5.5V, MSOP-08 package. The maximum power dis-
sipated in the part is given in Equation 1 below.
In most applications, the /INT output will be low for at most
a few milliseconds before the host resets it back to the high
state, making its duty cycle low enough that its contribution to
self-heating of the MIC384 is negligible. Similarly, the DATA
pin will in all likelihood have a duty cycle of substantially less
than 25% in the low state. These considerations, combined
with more typical device and application parameters, give a
better system-level view of device self-heating in interrupt-
mode. This is illustrated in Equation 2.
If the part is to be used in comparator mode, calculations
similar to those shown above (accounting for the expected
value and duty cycle of I
OL(INT)
) will give a good estimate of
the temperature error due to self-heating.
In any application, the best test is to verify performance
Vendor
Part Number
Package
Fairchild
MMBT3906
SOT-23
On Semiconductor
MMBT3906L
SOT-23
Phillips Semiconductor
PMBT3906
SOT-23
Samsung
KST3906-TF
SOT-23
Table 6. Transistors Suitable for Remote Temperature Sensing Use
against calculation in the nal application environment. This
is especially true when dealing with systems for which some
of the thermal data (e.g., PC board thermal conductivity and
ambient temperature) may be poorly dened or unobtainable
except by empirical means.
Series resistance
The operation of the MIC384 depends upon sensing the
擵
CB-E
of a diode-connected PNP transistor ( diode ) at two
different current levels. For remote temperature measure-
ments, this is done using external diodes connected between
T1, T2 and ground.
Since this technique relies upon measuring the relatively
small voltage difference resulting from two levels of current
through the external diodes, any resistance in series with
those diodes will cause an error in the temperature read-
ing from the MIC384. A good rule of thumb is this: for each
ohm in series with a zone's external transistor, there will be
a 0.9癈 error in the MIC384s temperature measurement. It
isnt difcult to keep the series resistance well below an ohm
(typically < 0.1?, so this will rarely be an issue.
Filter capacitor selection
It is sometimes desirable to use a lter capacitor between
the T1 and/or T2 pins and the GND pin of the MIC384. The
use of these capacitors is recommended in environments
with a lot of high frequency noise (such as digital switching
noise), or if long wires are used to attach to the remote di-
odes. The maximum recommended total capacitance from
the T1 or T2 pin to GND is 2700pF. This typically suggests
the use of 2200pF NP0 or C0G ceramic capacitors with a
10% tolerance.
If a remote diode is to be at a distance of more than H 6"12"
from the MIC384, using twisted pair wiring or shielded micro-
phone cable for the connections to the diode can signicantly
help reduce noise pickup. If using a long run of shielded
cable, remember to subtract the cables conductor-to-shield
capacitance from the 2700pF maximum total capacitance.
Equation 1. Worst-Case Self-Heating
Equation 2. Real-World Self-heating Example
P
D
= [(I
DD
x V
DD
) + (I
OL(DATA)
) x V
OL(DATA)
+ (I
OL(/INT)
x V
OL(/INT)
)]
P
D
= [(0.75mA x 5.5V) + (6mA x 0.8V) + (6mA x 0.8V)]
P
D
= 13.73mW
R
q(j-a)
of MSOP - 08 package is 206癈/W
Maximum T
J
relative to T
A
due to self heating is 13.73mW x 206癈/W = 2.83癈
[(0.35mA I
DD(typ)
x 3.3V) + (25% x 1.5mA I
OL(DATA)
) x 0.3V) + (1% x 1.5mA I
OL(/INT)
x 0.3V)] = 1.27mW
T
J
= (1.27mW x 206癈/W)
T
J
= 0.262癈
相关PDF资料 |
PDF描述 |
|---|---|
| EMC35DRAN-S734 | CONN EDGECARD 70POS .100 R/A PCB |
| XC9572XL-10CS48I | IC CPLD 72 MCELL I-TEMP 48-CSP |
| EMC40DRTH-S93 | CONN EDGECARD 80POS DIP .100 SLD |
| XCR3032XL-7CS48C | IC ISP CPLD 32 MCELL 3.3V 48-CSA |
| GEC12DRTH | CONN EDGECARD 24POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC384-3BM | 功能描述:IC SUPERVSR THERM LOC/REM 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| MIC384-3BM TR | 功能描述:IC SUPERVSR THERM LOC/REM 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| MIC384-3BMM | 功能描述:IC SUPERVISR THERM LOC/REM 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| MIC384-3BMM TR | 功能描述:IC SUPERVISR THERM LOC/REM 8MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| MIC384-3YM | 功能描述:板上安装温度传感器 3-zone thermal supervisor; SOIC-08 - Lead Free RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。