- 您现在的位置：买卖IC网 > PDF目录19717 > MIC39150-1.65BT (Micrel Inc)IC REG LDO 1.65V 1.5A TO220 PDF资料下载
参数资料
| 型号： | MIC39150-1.65BT |
| 厂商： | Micrel Inc |
| 文件页数： | 10/14页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.65V 1.5A TO220 |
| 标准包装： | 50 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.65V |
| 输入电压： | 2.25 V ~ 16 V |
| 电压 - 压降（标准）： | 0.375V @ 1.5A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 1.5A（最小） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 通孔 |
| 封装/外壳： | TO-220-3 |
| 供应商设备封装： | TO-220-3 |
| 包装： | 管件 |
Micrel, Inc.
Application Information
The MIC39150/1/2 are high-performance, low-dropout
voltage regulators suitable for moderate to high-current
voltage regulator applications. Its 500mV dropout
voltage at full load and overtemperature makes it
especially valuable in battery-powered systems and as
high-efficiency noise filters in post-regulator applications.
Unlike older NPN-pass transistor designs, where the
minimum dropout voltage is limited by the base-to-
emitter voltage drop and collector-to-emitter saturation
voltage, dropout performance of the PNP output of these
devices is limited only by the low V CE saturation voltage.
A trade-off for the low dropout voltage is a varying base
drive requirement. Micrel’s Super β eta PNP ? process
reduces this drive requirement to only 2% to 5% of the
load current. The MIC39150/1/2 regulators are fully
protected from damage due to fault conditions. Current
limiting is provided. This limiting is linear; output current
during overload conditions is constant. Thermal
shutdown disables the device when the die temperature
exceeds the maximum safe operating temperature.
Transient protection allows device (and load) survival
even when the input voltage spikes above and below
nominal. The output structure of these regulators allows
voltages in excess of the desired output voltage to be
applied without reverse current flow.
Thermal Design
Linear regulators are simple to use. The most
complicated design parameters to consider are thermal
characteristics. Thermal design requires the following
application-specific parameters:
? Maximum ambient temperature (T A )
? Output Current (I OUT )
? Output Voltage (V OUT )
MIC39150/39151/39152
distribute the heat between this resistor and the
regulator. The low dropout properties of Micrel Super
β eta PNP ? regulators allow significant reductions in
regulator power dissipation and the associated heat sink
without compromising performance. When this technique
is employed, a capacitor of at least 1μF is needed
directly between the input and regulator ground.
Refer to Application Note 9 for further details and
examples on thermal design and heat sink specification.
With no heat sink in the application, calculate the
junction temperature to determine the maximum power
dissipation that will be allowed before exceeding the
maximum junction temperature of the MIC39152. The
maximum power allowed can be calculated using the
thermal resistance ( θ JA ) of the TO-252 (D-Pak) adhering
to the following criteria for the PCB design: 2 oz. copper
and 100mm 2 copper area for the MIC39152.
For example, given an expected maximum ambient
temperature (T A ) of 75 ° C with V IN = 2.25V, V OUT = 1.75V,
and I OUT = 1.5A, first calculate the expected P D using
Equation (1);
P D = (2.25V – 1.75V)1.5A + (2.25V)(0.017A) = 0.788W
Next, calcualte the junction temperature for the expected
power dissipation.
T J = ( θ JA × P D ) + T A = (56 ° C/W × 0.788W) + 75 ° C
= 119.14 ° C
Now determine the maximum power dissipation allowed
that would not exceed the IC’s maximum junction
temperature (125 ° C) without the use of a heat sink by
P D(MAX) = (T J(MAX) – T A )/ θ JA = (125 ° C – 75 ° C)/(56 ° C/W)
= 0.893W
? Input Voltage (V IN )
? Ground Current (I GND )
First, calculate the power dissipation of the regulator
from these numbers and the device parameters from this
datasheet.
V IN
C IN
MIC39150-x.x
IN OUT
GND
V OU T
C OU T
P D = (V IN ? V OUT ) I OUT + V IN I GND
? ( θ JC + θ CS )
θ SA =
where the ground current is approximated by using
numbers from the “Electrical Characteristics” or “Typical
Characteristics.” Then the heat sink thermal resistance is
determined with this formula:
T J(max) ? T A
P D
Where T J(max) ≤ 125°C and θ CS is between 0° and 2°C/W.
The heat sink may be significantly reduced in
applications where the minimum input voltage is known
and is large compared with the dropout voltage. Use a
series input resistor to drop excessive voltage and
Figure 1. Capacitor Requirements
Output Capacitor
The MIC39150/1/2 requires an output capacitor to
maintain stability and improve transient response. See
Figure 1. Proper capacitor selection is important to
ensure proper operation. TheMIC39150/1/2 output
capacitor selection is dependent upon the ESR
(equivalent series resistance) of the output capacitor to
maintain stability. When the output capacitor is 10μF or
greater, the output capacitor should have an ESR less
than 2 ? . This will improve transient response as well as
October 2009
10
M9999-102309-A
相关PDF资料 |
PDF描述 |
|---|---|
| 171-025-213R021 | CONN DB25 FEMALE DIP SLD NICKEL |
| EEM30DRSH | CONN EDGECARD 60POS DIP .156 SLD |
| TOP261LN | IC OFFLINE SWIT PROG OVP 7FESIP |
| EEM28DRMS | CONN EDGECARD 56POS .156 WW |
| RCB105DHLT | CONN EDGECARD 210PS DIP .050 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC3915018WU | 制造商:Micrel Inc 功能描述: |
| MIC39150-2.5BT | 功能描述:IC REG LDO 2.5V 1.5A TO-220 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC39150-2.5BU | 功能描述:IC REG LDO 2.5V 1.5A TO263 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC39150-2.5BU TR | 功能描述:IC REG LDO 2.5V 1.5A TO-263 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC39150-2.5WT | 功能描述:低压差稳压器 - LDO 1.5A 1.0% Fixed Voltage LDO(ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。