- 您现在的位置：买卖IC网 > PDF目录19801 > MIC39300-1.8BU (Micrel Inc)IC REG LDO 1.8V 3A TO263 PDF资料下载
参数资料
| 型号： | MIC39300-1.8BU |
| 厂商： | Micrel Inc |
| 文件页数： | 11/13页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.8V 3A TO263 |
| 标准包装： | 50 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.8V |
| 输入电压： | 2.5 V ~ 16 V |
| 电压 - 压降（标准）： | 0.385V @ 3A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 3A（最小） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-4，D²Pak（3 引线+接片），TO-263AA |
| 供应商设备封装： | TO-263-3 |
| 包装： | 管件 |
R1 = R2 × ? ? OUT ? 1 ? ?
Micrel, Inc.
Transient Response and 3.3V to 2.5V and 2.5V to
1.8V Conversions
The MIC39300/1/2 has excellent transient response to
variations in input voltage and load current. The device
has been designed to respond quickly to load current
variations and input voltage variations. Large output
capacitors are not required to obtain this performance. A
standard 47 μ F output capacitor, preferably tantalum, is
all that is required. Larger values help to improve
performance even further.
By virtue of its low-dropout voltage, this device does not
saturate into dropout as readily as similar NPN-based
designs. When converting from 3.3V to 2.5V or 2.5V to
1.8V, the NPN-based regulators are already operating in
dropout, with typical dropout requirements of 1.2V or
greater. To convert down to 2.5V without operating in
dropout, NPN-based regulators require an input voltage
of 3.7V at the very least. The MIC39300/1 regulator will
provide excellent performance with an input as low as
3.0V or 2.5V. This gives the PNP-based regulators a
distinct advantage over older, NPN-based linear
regulators.
Minimum Load Current
The MIC39300/1/2 regulators are specified between
finite loads. If the output current is too small, leakage
currents dominate and the output voltage rises. A 10mA
minimum load current is necessary for proper regulation.
Error Flag
The MIC39301 version features an error flag circuit
which monitors the output voltage and signals an error
condition when the voltage drops 5% below the nominal
output voltage. The error flag is an open-collector output
that can sink 10mA during a fault condition.
Low output voltage can be caused by a number of
problems, including an overcurrent fault (device in
current limit) or low input voltage. The flag is inoperative
during overtemperature shutdown.
When the error flag is not used, it is best to leave it
open. A pull-up resistor from FLG to either V IN or V OUT is
required for proper operation.
MIC39300/39301/39302
Enable Input
The MIC39301/2 features an enable input for on/off
control of the device. The enable input’s shutdown state
draws “zero” current (only microamperes of leakage).
The enable input is TTL/CMOS compatible for simple
logic interface, but can be connected to up to 20V. When
enabled, it draws approximately 15 μ A.
Adjustable Regulator Design
Figure 2. Adjustable Regulator with Resistors
The MIC39302 allows programming the output voltage
anywhere between 1.24V and 15.5V. Two resistors are
used. The resistor values are calculated by:
? V ?
? 1.240 ?
Where V OUT is the desired output voltage. Figure 2
shows component de ? nition. Applications with widely
varying load currents may scale the resistors to draw the
minimum load current required for proper operation (see
Minimum Load Current section).
October 2009
11
M9999-102309-A
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J42-CW-B1 | CONVERTER MOD DC/DC 15V 100W |
| VI-B7V-CY-F1 | CONVERTER MOD DC/DC 5.8V 50W |
| LMK107SD123KA-T | CAP CER 0.012UF 10V 10% 0603 |
| HCM10DRUH | CONN EDGECARD 20POS .156 DIP SLD |
| ISL6141IBZA | IC CTRLR HOT PLUG NEG VOLT 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC39300-2.5BT | 功能描述:IC REG LDO 2.5V 3A TO220-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC39300-2.5BU | 功能描述:IC REG LDO 2.5V 3A TO263 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC39300-2.5BU TR | 功能描述:IC REG LDO 2.5V 3A TO263 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC39300-2.5BUTR | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| MIC39300-2.5WT | 功能描述:低压差稳压器 - LDO 3.0A 1.0% Fixed Voltage LDO(ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。