参数资料
| 型号： | MIC39300-1.8WU |
| 厂商： | Micrel Inc |
| 文件页数： | 10/13页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.8V 3A TO263 |
| 标准包装： | 50 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.8V |
| 输入电压： | 2.5 V ~ 16 V |
| 电压 - 压降（标准）： | 0.385V @ 3A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 3A（最小） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-4，D²Pak（3 引线+接片），TO-263AA |
| 供应商设备封装： | TO-263-3 |
| 包装： | 管件 |
| 产品目录页面： | 1108 (CN2011-ZH PDF) |
| 其它名称： | 576-1178 |
? ( θ JC + θ CS )
θ SA =
Micrel, Inc.
Application Information
The MIC39300/1/2 are high-performance, low-dropout
voltage regulators suitable for moderate to high-current
voltage regulator applications. Its 550mV dropout
voltage at full load makes it especially valuable in
battery-powered systems and as a high-efficiency noise
filter in post-regulator applications. Unlike older NPN-
pass transistor designs, where the minimum dropout
voltage is limited by the base-to-emitter voltage drop and
collector-to-emitter saturation voltage, dropout
performance of the PNP output of these devices is
limited only by the low V CE saturation voltage.
A trade-off for the low dropout voltage is a varying base
drive requirement. Micrel’s Super β eta PNP ? process
reduces this drive requirement to only 2% to 5% of the
load current.
The MIC39300/1/2 regulators are fully protected from
damage due to fault conditions. Current limiting is
provided. This limiting is linear; output current during
overload conditions is constant. Thermal shutdown
disables the device when the die temperature exceeds
the maximum safe operating temperature. Transient
protection allows device (and load) survival even when
the input voltage spikes above and below nominal. The
output structure of these regulators allows voltages in
excess of the desired output voltage to be applied
without reverse current flow.
Thermal Design
Linear regulators are simple to use. The most
complicated design parameters to consider are thermal
characteristics. Thermal design requires four application-
specific parameters:
? Maximum ambient temperature (T A )
? Output Current (I OUT )
? Output Voltage (V OUT )
? Input Voltage (V IN )
? Ground Current (I GND )
Calculate the power dissipation of the regulator from
these numbers and the device parameters from this
datasheet, where the ground current is taken from the
data sheet.
P D = (V IN – V OUT ) I OUT + V IN × I GND
The heat sink thermal resistance is determined by:
T J(max) ? T A
P D
where T J(max) ≤ 125°C and θ CS is between 0° and 2°C/W.
The heat sink may be significantly reduced in
applications where the minimum input voltage is known
and is large compared with the dropout voltage. Use a
series input resistor to drop excessive voltage and
MIC39300/39301/39302
distribute the heat between this resistor and the
regulator. The low dropout properties of Micrel Super
β eta PNP ? regulators allow significant reductions in
regulator power dissipation and the associated heat sink
without compromising performance. When this technique
is employed, a capacitor of at least 1.0 μ F is needed
directly between the input and regulator ground.
Refer to “Application Note 9” for further details and
examples on thermal design and heat sink specification.
Figure 1. Capacitor Requirements
Output Capacitor
The MIC39300/1/2 requires an output capacitor to
maintain stability and improve transient response.
Proper capacitor selection is important to ensure proper
operation. The MIC39300/1/2 output capacitor selection
is dependent upon the ESR (equivalent series
resistance) of the output capacitor to maintain stability.
When the output capacitor is 47 μ F or greater, the output
capacitor should have less than 1 ? of ESR. This will
improve transient response as well as promote stability.
Ultralow ESR capacitors, such as ceramic chip
capacitors may promote instability. These very low ESR
levels may cause an oscillation and/or underdamped
transient response. A low-ESR solid tantalum capacitor
works extremely well and provides good transient
response and stability over temperature. Aluminum
electrolytics can also be used, as long as the ESR of the
capacitor is < 1 ? .
The value of the output capacitor can be increased
without limit. Higher capacitance values help to improve
transient response and ripple rejection and reduce
output noise.
Input Capacitor
An input capacitor of 1 μ F or greater is recommended
when the device is more than 4 inches away from the
bulk ac supply capacitance, or when the supply is a
battery. Small, surface mount, ceramic chip capacitors
can be used for the bypassing. Larger values will help to
improve ripple rejection by bypassing the input to the
regulator, further improving the integrity of the output
voltage.
October 2009
10
M9999-102309-A
相关PDF资料 |
PDF描述 |
|---|---|
| 250MXG470MEFCSN30X25 | CAP ALUM 470UF 250V 20% SNAP-IN |
| MIC39300-2.5WU | IC REG LDO 2.5V 3A TO-263 |
| 250VXG470MEFCSN30X25 | CAP ALUM 470UF 250V 20% SNAP-IN |
| 160TXW330MEFC16X30 | CAP ALUM 330UF 160V 20% RADIAL |
| 180USC1000MEFCSN30X30 | CAP ALUM 1000UF 180V 20% SNAP-IN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC39300-2.5BT | 功能描述:IC REG LDO 2.5V 3A TO220-3 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC39300-2.5BU | 功能描述:IC REG LDO 2.5V 3A TO263 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC39300-2.5BU TR | 功能描述:IC REG LDO 2.5V 3A TO263 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC39300-2.5BUTR | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| MIC39300-2.5WT | 功能描述:低压差稳压器 - LDO 3.0A 1.0% Fixed Voltage LDO(ROHS Compliant) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。