参数资料
| 型号： | MIC39501-2.5WU |
| 厂商： | Micrel Inc |
| 文件页数： | 7/10页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.5V 5A TO-263-5 |
| 标准包装： | 50 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.5V |
| 输入电压： | 最高 16V |
| 电压 - 压降（标准）： | 0.4V @ 5A |
| 稳压器数量： | 1 |
| 电流 - 输出： | 5A（最小） |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-263-6，D²Pak（5 引线+接片），TO-263BA |
| 供应商设备封装： | TO-263-5 |
| 包装： | 管件 |
| 产品目录页面： | 1108 (CN2011-ZH PDF) |
| 其它名称： | 576-2312 MIC39501-2.5WU-ND |
MIC39500/39501
Applications Information
The MIC39500/1 is a high-performance low-dropout voltage
regulator suitable for moderate to high-current voltage regula-
tor applications. Its 400mV dropout voltage at full load makes
it especially valuable in battery-powered systems and as a
high-ef? ciency noise ? lter in post-regulator applications. Un-
like older NPN-pass transistor designs, where the minimum
dropout voltage is limited by the base-to-emitter voltage drop
and collector-to-emitter saturation voltage, dropout perfor-
mance of the PNP output of these devices is limited only by
the low V CE saturation voltage.
A trade-off for the low dropout voltage is a varying base drive
requirement. Micrel’s Super β eta PNP? process reduces this
drive requirement to only 2% to 5% of the load current.
The MIC39500/1 regulator is fully protected from damage due
to fault conditions. Current limiting is provided. This limiting is
linear; output current during overload conditions is constant.
Thermal shutdown disables the device when the die tempera-
ture exceeds the maximum safe operating temperature. Tran-
sient protection allows device (and load) survival even when
the input voltage spikes above and below nominal. The output
structure of these regulators allows voltages in excess of the de-
sired output voltage to be applied without reverse current ? ow.
Micrel
pared with the dropout voltage. Use a series input resistor
to drop excessive voltage and distribute the heat between
this resistor and the regulator. The low-dropout properties of
Micrel Super β eta PNP regulators allow signi? cant reductions
in regulator power dissipation and the associated heat sink
without compromising performance. When this technique
is employed, a capacitor of at least 1μF is needed directly
between the input and regulator ground.
Refer to Application Note 9 for further details and examples
on thermal design and heat sink speci? cation.
Output capacitor
The MIC39500/1 requires an output capacitor to maintain
stability and improve transient response. Proper capaci-
tor selection is important to ensure proper operation. The
MIC39500/1 output capacitor selection is dependent upon the
ESR (equivalent series resistance) of the output capacitor to
maintain stability. When the output capacitor is 47μF or greater,
the output capacitor should have less than 1? of ESR. This
will improve transient response as well as promote stability.
Ultra-low-ESR capacitors, such as ceramic chip capacitors
may promote instability. These very low ESR levels may
cause an oscillation and/or underdamped transient response.
When larger capacitors are used, the ESR requirement ap-
proaches zero. A 100μF ceramic capacitor can be used on
V IN
C IN
MIC39500-x.x
IN OUT
GND
V OUT
C OUT
the output while maintaining stability. A low-ESR 47μF solid
tantalum capacitor works extremely well and provides good
transient response and stability over temperature. Aluminum
electrolytics can also be used, as long as the ESR of the
capacitor is < 1?.
The value of the output capacitor can be increased without
limit. Higher capacitance values help to improve transient
Figure 1. Capacitor Requirements
Thermal Design
Linear regulators are simple to use. The most complicated
design parameters to consider are thermal characteristics.
Thermal design requires four application-speci? c param-
eters:
? Maximum ambient temperature (T A )
? Output Current (I OUT )
? Output Voltage (V OUT )
? Input Voltage (V IN )
? Ground Current (I GND )
Calculate the power dissipation of the regulator from these
numbers and the device parameters from this datasheet,
where the ground current is taken from data sheet.
P D = (V IN – V OUT ) × I OUT + V IN × I GND
The heat sink thermal resistance is determined by:
where:
T J (max) ≤ 125°C and θ CS is between 0° and 2°C/W.
The heat sink may be signi? cantly reduced in applications
where the minimum input voltage is known and is large com-
response and ripple rejection and reduce output noise.
Input capacitor
An input capacitor of 1μF or greater is recommended when
the device is more than 4 inches away from the bulk ac supply
capacitance, or when the supply is a battery. Small surface-
mount ceramic chip capacitors can be used for bypassing.
Larger values will help to improve ripple rejection by bypass-
ing the input to the regulator, further improving the integrity
of the output voltage.
Transient Response and 3.3V to 2.5V or 2.5V to 1.8V
Conversion
The MIC39500/1 has excellent transient response to varia-
tions in input voltage and load current. The device has been
designed to respond quickly to load current variations and
input voltage variations. Large output capacitors are not re-
quired to obtain this performance. A standard 47μF output
capacitor, preferably tantalum, is all that is required. Larger
values improve performance even further.
By virtue of its low-dropout voltage, this device does not
saturate into dropout as readily as similar NPN-based de-
signs. When converting from 3.3V to 2.5V, or 2.5V to 1.8V,
the NPN-based regulators are already operating in dropout,
with typical dropout requirements of 1.2V or greater. To con-
vert down to 2.5V without operating in dropout, NPN-based
regulators require an input voltage of 3.7V at the very least.
The MIC39500/1 regulator provides excellent performance
August 2005
7
M9999-082605-B
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6324CRZ-T | IC HYBRID CTRLR PWM DUAL 48-QFN |
| LT1963AEFE-3.3#PBF | IC REG LDO 3.3V 1.5A 16TSSOP |
| HIP6004DCRZ-T | IC CTRLR PWM VOLTAGE MON 20-QFN |
| LT1963AEFE-1.8#PBF | IC REG LDO 1.8V 1.5A 16TSSOP |
| HIP6004BCRZ-T | IC CTRLR PWM VOLTAGE MON 20-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC-3951 | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:6U CompactPCI? Dual PMC or CMC Carrier Board (64-bit/66 MHz) |
| MIC-3951-AE | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:6U CompactPCI? Dual PMC or CMC Carrier Board (64-bit/66 MHz) |
| MIC-3960 | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:6U CompactPCI? Media Carrier Board |
| MIC-3960-AE | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:6U CompactPCI? Media Carrier Board |
| MIC-3961 | 制造商:ADVANTECH 制造商全称:Advantech Co., Ltd. 功能描述:6U CompactPCI? PCI Carrier Board |
发布紧急采购，3分钟左右您将得到回复。