- 您现在的位置：买卖IC网 > PDF目录20454 > MIC4421CM TR (Micrel Inc)IC DRIVER MOSFET 9A LS 8-SOIC PDF资料下载
参数资料
| 型号： | MIC4421CM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER MOSFET 9A LS 8-SOIC |
| 标准包装： | 2,500 |
| 配置： | 低端 |
| 输入类型： | 反相 |
| 延迟时间： | 15ns |
| 电流 - 峰： | 9A |
| 配置数： | 1 |
| 输出数： | 1 |
| 电源电压： | 4.5 V ~ 18 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC4421CMTR MIC4421CMTR-ND |
MIC4421/4422
Capacitive Load Power Dissipation
Dissipation caused by a capacitive load is simply the energy
placed in, or removed from, the load capacitance by the
driver. The energy stored in a capacitor is described by the
equation:
E = 1/2 C V 2
As this energy is lost in the driver each time the load is charged
or discharged, for power dissipation calculations the 1/2 is
removed. This equation also shows that it is good practice
not to place more voltage in the capacitor than is necessary,
as dissipation increases as the square of the voltage applied
to the capacitor. For a driver with a capacitive load:
P L = f C (V S ) 2
where:
f = Operating Frequency
C = Load Capacitance
V S = Driver Supply Voltage
Inductive Load Power Dissipation
For inductive loads the situation is more complicated. For
the part of the cycle in which the driver is actively forcing
current into the inductor, the situation is the same as it is in
the resistive case:
P L1 = I 2 R O D
However, in this instance the R O required may be either
the on resistance of the driver when its output is in the high
state, or its on resistance when the driver is in the low state,
depending on how the inductor is connected, and this is still
only half the story. For the part of the cycle when the induc-
tor is forcing current through the driver, dissipation is best
described as
P L2 = I V D (1 – D)
where V D is the forward drop of the clamp diode in the driver
(generally around 0.7V). The two parts of the load dissipation
must be summed in to produce P L
P L = P L1 + P L2
Quiescent Power Dissipation
Quiescent power dissipation (P Q , as described in the input
section) depends on whether the input is high or low. A low
input will result in a maximum current drain (per driver) of
≤ 0.2mA; a logic high will result in a current drain of ≤ 3.0mA.
Quiescent power can therefore be found from:
P Q = V S [D I H + (1 – D) I L ]
where:
Micrel, Inc.
Transition Power Dissipation
Transition power is dissipated in the driver each time its
output changes state, because during the transition, for a
very brief interval, both the N- and P-channel MOSFETs in
the output totem-pole are ON simultaneously, and a current
is conducted through them from V S to ground. The transition
power dissipation is approximately:
P T = 2 f V S (A?s)
where (A?s) is a time-current factor derived from the typical
characteristic curve “Crossover Energy vs. Supply Volt-
age.”
Total power (P D ) then, as previously described is just
P D = P L + P Q + P T
De?nitions
C L = Load Capacitance in Farads.
D = Duty Cycle expressed as the fraction of time the
input to the driver is high.
f = Operating Frequency of the driver in Hertz
I H = Power supply current drawn by a driver when both
inputs are high and neither output is loaded.
I L = Power supply current drawn by a driver when both
inputs are low and neither output is loaded.
I D = Output current from a driver in Amps.
P D = Total power dissipated in a driver in Watts.
P L = Power dissipated in the driver due to the driver ’s
load in Watts.
P Q = Power dissipated in a quiescent driver in Watts.
P T = Power dissipated in a driver when the output
changes states (“shoot-through current”) in Watts.
NOTE: The “shoot-through” current from a dual
transition (once up, once down) for both drivers is
stated in Figure 7 in ampere-nanoseconds. This
?gure must be multiplied by the number of repeti-
tions per second (frequency) to ?nd Watts.
R O = Output resistance of a driver in Ohms.
V S = Power supply voltage to the IC in Volts.
I H =
I L =
D =
V S =
quiescent current with input high
quiescent current with input low
fraction of time input is high (duty cycle)
power supply voltage
August 2005
9
M9999-081005
相关PDF资料 |
PDF描述 |
|---|---|
| IXDD514PI | IC GATE DRIVER 14A 8-DIP |
| T521V336M025ATE060 | CAP TANT 33UF 25V 20% 2917 |
| EBM28MMAD | CARDEDGE MALE 56POS .156 R/A AU |
| IXDD514D1T/R | IC GATE DRIVER 14A 6-DFN |
| VE-B31-CX-F3 | CONVERTER MOD DC/DC 12V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC4421CN | 功能描述:IC DRIVER MOSFET 9A LS 8-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
| MIC4421CT | 功能描述:IC DRIVER MOSFET 9A LS TO-220-5 RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
| MIC4421YM | 功能描述:功率驱动器IC High Speed, 9A Low Side MOSFET Driver (Lead Free) RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MIC4421YM TR | 功能描述:功率驱动器IC High Speed, 9A Low Side MOSFET Driver (Lead Free) RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MIC4421YM-TR | 制造商:Micrel Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。