参数资料
| 型号： | MIC4684BM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 2/16页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 2A 8SOIC |
| 标准包装： | 2,500 |
| 系列： | SuperSwitcher™ |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 1.235V |
| 输入电压： | 4 V ~ 30 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 200kHz |
| 电流 - 输出： | 2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-SOIC |
| 其它名称： | MIC4684BMTR MIC4684BMTR-ND |
Micrel, Inc.
Pin Configuration
MIC4684
SW
GND
VIN
BS
1
2
3
4
8
7
6
5
EN
GND
GND
FB
8-Pin SOP (M)
Pin Description
Pin Number
1
2, 6, 7
3
4
5
8
Pin Name
SW
GND
IN
BS
FB
EN
Pin Function
Switch (Output): Emitter of NPN output switch. Connect to external storage
inductor and Shottky diode.
Ground
Supply (Input): Unregulated +4V to 30V supply voltage (34V transient)
Booststrap Voltage Node (External Component): Connect to external boost
capacitor.
Feedback (Input): Outback voltage feedback to regulator. Connect to output
of supply for fixed versions. Connect to 1.23V tap of resistive divider for
adjustable versions.
Enable (Input): Logic high = enable; logic low = shutdown
Detailed Pin Description
Switch (SW, pin 1)
The switch pin is tied to the emitter of the main internal NPN
transistor. This pin is biased up to the input voltage minus the
V SAT of the main NPN pass element. The emitter is also driven
negative when the output inductor ’s magnetic field collapses
at turn-off. During the OFF time the SW pin is clamped by
the output schottky diode to a –0.5V typically.
Ground (GND, pins 2,6,7)
There are two main areas of concern when it comes to the
ground pin, EMI and ground current. In a buck regulator
or any other non-isolated switching regulator the output
capacitor(s) and diode(s) ground is referenced back to the
switching regulator ’s or controller ’s ground pin. Any resistance
between these reference points causes an offset voltage/IR
drop proportional to load current and poor load regulation.
This is why its important to keep the output grounds placed
as close as possible to the switching regulator ’s ground pin.
To keep radiated EMI to a minimum its necessary to place
the input capacitor ground lead as close as possible to the
switching regulators ground pin.
Input Voltage (V IN , pin 3)
The V IN pin is the collector of the main NPN pass element.
This pin is also connected to the internal regulator. The output
diode or clamping diode should have its cathode as close as
possible to this point to avoid voltage spikes adding to the
voltage across the collector.
Bootstrap (BS, pin 4)
The bootstrap pin in conjunction with the external bootstrap
capacitor provides a bias voltage higher than the input volt -
age to the MIC4684’s main NPN pass element. The bootstrap
capacitor sees the dv/dt of the switching action at the SW
pin as an AC voltage. The bootstrap capacitor then couples
the AC voltage back to the BS pin plus the dc offset of V IN
where it is rectified and used to provide additional drive to
the main switch, in this case a NPN transistor.
This additional drive reduces the NPN’s saturation voltage and
increases efficiency, from a V SAT of 1.8V, and 75% efficiency
to a V SAT of 0.5V and 88% efficiency respectively.
Feedback (FB, pin 5)
The feedback pin is tied to the inverting side of a GM error
amplifier. The noninverting side is tied to a 1.235V bandgap
reference. Fixed voltage versions have an internal voltage
divider from the feedback pin. Adjustable versions require an
external resistor voltage divider from the output to ground,
with the center tied to the feedback pin.
Enable (EN, pin 8)
The enable (EN) input is used to turn on the regulator and is
TTL compatible. Note: connect the enable pin to the input if
unused. A logic-high enables the regulator. A logic-low shuts
down the regulator and reduces the stand-by quiescent
input current to typically 150μA. The enable pin has an up -
per threshold of 2.0V minimum and lower threshold of 0.8V
maximum. The hysterisis provided by the upper and lower
thresholds acts as an UVLO and prevents unwanted turn on
of the regulator due to noise.
January 2010
2
M9999-012610
相关PDF资料 |
PDF描述 |
|---|---|
| MIC4685BR TR | IC REG BUCK ADJ 3A SPAK-7 |
| MIC4690BM TR | IC REG BUCK ADJ 1A 8SOIC |
| MIC47050-1.2YML TR | IC REG LDO 1.2V .5A 6MLF |
| MIC47100-0.8YML TR | IC REG LDO 0.8V 1A 8-MLF |
| MIC47150WD TR | IC REG LDO ADJ 1.5A TO-252-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC4684YM | 功能描述:直流/直流开关调节器 SO-8 Efficient Simple Buck Regulator (Lead Free) RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC4684YM TR | 功能描述:直流/直流开关调节器 SO-8 Efficient Simple Buck Regulator (Lead Free) RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC4684YM | 制造商:Micrel Inc 功能描述:IC VOLTAGE REGULATOR SOIC |
| MIC4684YM | 制造商:Micrel Inc 功能描述:Voltage Regulator IC |
| MIC4684YMTR | 制造商:Micrel 功能描述:Conv DC-DC Single Step Down 4V to 30V |
发布紧急采购，3分钟左右您将得到回复。