参数资料
| 型号： | MIC47050-1.2YML TR |
| 厂商： | Micrel Inc |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.2V .5A 6MLF |
| 特色产品： | MIC47050 Voltage Regulators |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.2V |
| 输入电压： | 最高 3.6V |
| 电压 - 压降（标准）： | 0.044V @ 500mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 500mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-VQFN 裸露焊盘，6-MLF? |
| 供应商设备封装： | 6-MLF?（2x2） |
| 包装： | 标准包装 |
| 其它名称： | 576-3666-6 |
Micrel, Inc.
Power Good (PGOOD)
The Power Good (PGOOD) pin is an open drain output
that goes low when the output voltage (fixed version)
drops below the PGOOD threshold voltage.
The pull-up resistor value should be large enough to
guarantee a proper “low” voltage when the PGOOD pin
pulls low. The PGOOD low voltage is typically 0.1V at
MIC47050
T J(MAX) = 125°C, the maximum junction temperature of
the die.
θ JA thermal resistance = 90°C/W.
Table 1 shows junction-to-ambient thermal resistance for
the MIC47050 in the MLF ? or Thin MLF ? package.
250μA current. A 10k ? resistor or greater is
recommended when pulling up to 3.3V bias.
Package
θ JA Recommended
Min. Footprint
θ JC
90°C/W
If the PGOOD function is not required, the PGOOD pin
may be left unconnected.
Thermal Shutdown
The MIC47050 has an internal over-temperature
6-pin 2mm x 2mm MLF ? 90°C/W
6-pin 2mm x 2mm
Thin MLF ?
Table 1. Thermal Resistance
45°C/W
45°C/W
protection feature. This feature is for protection only.
The device should never be intentionally operated near
this temperature as this may reduce long term reliability.
The device will turn off when the over-temperature
threshold is exceeded. A 20°C hysteresis is built in to
allow the device to cool before turning back on.
Thermal Considerations
The MIC47050 is designed to provide 0.5A of continuous
current in a very small package. Maximum ambient
operating temperature can be calculated based on the
output current and the voltage drop across the part.
Given that the input voltage is 1.8V, the output voltage is
1.2V and the output current is 0.5A. The actual power
dissipation of the regulator circuit can be determined
using the equation:
P D ? ? V IN ? V OUT ? ? I OUT ? V IN ? I GND ? V BIAS ? I BIAS
Because this device is CMOS, the ground current is
insignificant for power dissipation and can be ignored for
this calculation.
P D ? ? 1.8V ? 1.2V ? ? 0.5A ? 0.3W
To determine the maximum ambient operating
temperature of the package, use the junction-to-ambient
thermal resistance of the device and the following basic
equation:
Substituting P D for P D(max) and solving for the ambient
operating temperature will give the maximum operating
conditions for the regulator circuit. The junction-to-
ambient thermal resistance for the minimum footprint is
90°C/W. The maximum power dissipation must not be
exceeded for proper operation. For example, when
operating the MIC47050-1.2YML at an input voltage of
1.8V and a 0.5A load with a minimum footprint layout,
the maximum ambient operating temperature T A can be
determined as follows:
T A ? T J(MAX) ? Θ JA ? P D(MAX)
T A ? 125 ? C ? 90 ? C/W ? 0.3W
T A ? 98 ? C
Therefore, a 1.2V application with 0.5A of output current
can accept an ambient operating temperature of 98°C in
a 2mm x 2mm MLF ? or Thin MLF ? package.
Thermal Measurements
Measuring the IC’s case temperature is recommended to
insure it is within its operating limits. Although this might
seem like a very elementary task, it is easy to get
erroneous results. The most common mistake is to use
the standard thermal couple that comes with a thermal
meter. This thermal couple wire gauge is large, typically
22 gauge, and behaves like a heatsink, resulting in a
lower case measurement.
Two methods of temperature measurement are using a
P D(MAX) ?
? T J(MAX) ? T A ?
? ?
? ?
? Θ JA ?
smaller thermal couple wire or an infrared thermometer.
If a thermal couple wire is used, it must be constructed
of 36 gauge wire or higher (smaller wire size) to
minimize the wire heat-sinking effect.
April 2012
11
M9999-040312-B
相关PDF资料 |
PDF描述 |
|---|---|
| MIC47100-0.8YML TR | IC REG LDO 0.8V 1A 8-MLF |
| MIC47150WD TR | IC REG LDO ADJ 1.5A TO-252-5 |
| MIC4720YMME TR | IC REG BUCK ADJ 2A 10MSOP |
| MIC4721YMMTR | IC REG BUCK ADJ 1.5A 10MSOP |
| MIC4722YML TR | IC REG BUCK ADJ 3A 12MLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC47050YML | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:500mA ULDO? with Low Input and Low Output Voltage |
| MIC47050YML TR | 功能描述:低压差稳压器 - LDO Low Vin Single 500mA Adjustable LDO in Small 2mm x2mm MLF RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC47050YML-TR | 功能描述:Linear Voltage Regulator IC Positive Adjustable 1 Output 0.4 V ~ 2 V 500mA 6-MLF? (2x2) 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:有效 稳压器拓扑:正，可调式 电压 - 输出:0.4 V ~ 2 V 电流 - 输出:500mA 电压 - 跌落（典型值）:0.044V @ 500mA 稳压器数:1 电压 - 输入:1 V ~ 3.6 V 电流 - 限制（最小值）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-VQFN 裸露焊盘，6-MLF? 供应商器件封装:6-MLF?（2x2） 标准包装:1 |
| MIC47050YMT | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:500mA ULDO? with Low Input and Low Output Voltage |
| MIC47050YMT TR | 功能描述:低压差稳压器 - LDO Low Vin Single 500mA Adjustable LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。