- 您现在的位置：买卖IC网 > PDF目录14872 > MIC4721YMM (Micrel Inc)IC REG BUCK ADJ 1.5A 10MSOP PDF资料下载
参数资料
| 型号： | MIC4721YMM |
| 厂商： | Micrel Inc |
| 文件页数： | 15/19页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.5A 10MSOP |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 可调至 1V |
| 输入电压： | 2.7 V ~ 5.5 V |
| 频率 - 开关： | 2MHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 10-MSOP |
| 产品目录页面： | 1093 (CN2011-ZH PDF) |
| 其它名称： | 576-1655-5 MIC4721YMM-ND |
Micrel, Inc.
MIC4721
As one can see the typical phase margin, using the
same resistor values as before without a feedforward
capacitor results in 33.6 degrees of phase margin. Our
prior measurement with a feedforward capacitor yielded
? V =
10
dBm
10
× 1 mW × 50 ? × 2
. 707
Z OUT =
× 1 mW × 50 ? × 2
? V =
a phase margin of 47 degrees. The feedforward
capacitor has given us a phase boost of 13.4 degrees
(47 degrees – 33.6 Degrees = 13.4 Degrees).
Output Impedance and Transient Response
Output impedance, simply stated, is the amount of
output voltage deviation vs. the load current deviation.
The lower the output impedance, the better.
? V OUT
? I OUT
Output impedance for a buck regulator is the parallel
impedance of the output capacitor and the MOSFET and
inductor divided by the gain:
and peak to peak current:
dBm
10
10
. 707 × R LOAD
The following graph shows output impedance vs
frequency at 2A load current sweeping the AC current
from 10Hz to 10MHz, at 1A peak-to-peak amplitude.
Z TOTAL =
R DSON + DCR + X L
GAIN
|| X COUT
To measure output impedance vs. frequency, the load
current must be swept across the frequencies measured,
while the output voltage is monitored. Figure 9 shows a
test set-up to measure output impedance from 10Hz to
1MHz using the MIC5190 high speed controller.
From this graph, you can see the effects of bandwidth
and output capacitance. For frequencies <200KHz, the
output impedance is dominated by the gain and
inductance. For frequencies >200KHz, the output
impedance is dominated by the capacitance. A good
approximation for transient response can be calculated
from determining the frequency of the load step in amps
per second:
f =
A / sec
2 π
Then, determine the output impedance by looking at the
Figure 9. Output Impedance Measurement
By setting up a network analyzer to sweep the feedback
current, while monitoring the output of the voltage
regulator and the voltage across the load resistance,
output impedance is easily obtainable. To keep the
current from being too high, a DC offset needs to be
applied to the network analyzer’s source signal. This can
be done with an external supply and 50 ? resistor. Make
sure that the currents are verified with an oscilloscope
output impedance vs frequency graph. Next, calculate
the voltage deviation times the load step;
? V OUT = ? I OUT ×Z OUT
The output impedance graph shows the relationship
between supply voltage and output impedance. This is
caused by the lower R DSON of the high side MOSFET
and the increase in gain with increased supply voltages.
This explains why higher supply voltages have better
transient response.
first, to ensure the integrity of the signal measurement. It
is always a good idea to monitor the A and R
measurements with a scope while you are sweeping it.
↓ Z TOTAL =
↓ R DSON + DCR + X L
↑ GAIN
|| X COUT
To convert the network analyzer data from dBm to
something more useful (such as peak to peak voltage
and current in our case):
To properly measure ripple on either input or output of a
switching regulator, a proper ring in tip measurement is
required. Standard oscilloscope probes come with a
grounding clip, or a long wire with an alligator clip.
May 2007
15
M9999-052907-A
相关PDF资料 |
PDF描述 |
|---|---|
| VE-JVM-EY-F1 | CONVERTER MOD DC/DC 10V 50W |
| VE-JVL-EY-F4 | CONVERTER MOD DC/DC 28V 50W |
| VE-JVL-EY-F3 | CONVERTER MOD DC/DC 28V 50W |
| VE-JVL-EY-F2 | CONVERTER MOD DC/DC 28V 50W |
| VI-24K-EY-F1 | CONVERTER MOD DC/DC 40V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC4721YMM TR | 功能描述:直流/直流开关调节器 1.5A 2MHz Buck Regulator RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC4721YMMTR | 功能描述:IC REG BUCK ADJ 1.5A 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:20 系列:SIMPLE SWITCHER® 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:12V 输入电压:4 V ~ 60 V PWM 型:电压模式 频率 - 开关:52kHz 电流 - 输出:1A 同步整流器:无 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 包装:管件 供应商设备封装:16-DIP 其它名称:*LM2575HVN-12LM2575HVN-12 |
| MIC4722 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:3mm x 3mm 2.7MHz 3A PWM Buck Regulator |
| MIC4722_10 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:3mm x 3mm 2.7MHz 3A PWM Buck Regulator |
| MIC4722YML | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
发布紧急采购，3分钟左右您将得到回复。