- 您现在的位置：买卖IC网 > PDF目录19365 > MIC4832YMM (Micrel Inc)IC DRIVER LN 220VP-P EL 8-MSOP PDF资料下载
参数资料
| 型号： | MIC4832YMM |
| 厂商： | Micrel Inc |
| 文件页数： | 7/11页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER LN 220VP-P EL 8-MSOP |
| 标准包装： | 100 |
| 类型： | EL 灯驱动器 |
| 频率： | 60Hz ~ 1kHz |
| 电流 - 电源： | 45µA |
| 电源电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
| 产品目录页面： | 1086 (CN2011-ZH PDF) |
| 其它名称： | 576-2127-5 576-2127-5-ND 576-2977-5 |
Micrel
Application Information
Inductor
A 220μH Murata (LQH4C221K04) inductor is
recommended for most applications. Generally,
inductors with smaller values can handle more
current. Lowering the inductance allows the boost
regulator to draw more input current to deliver more
energy every cycle. As a result, a lower value
inductor may be used to drive larger panels or make
the current panel brighter. However, caution is
required as using a low value inductor with a low
switching frequency may result in voltages
exceeding the absolute maximum rating of the
switch node and/or the CS pin. If the application
uses a low input voltage (1.8 to 3V), a lower value
inductor, such as 100μH, may be used in order to
drive the EL lamp at max brightness without issue.
Diode
The diode must have a high reverse voltage (150V),
since the output voltage at the CS pin can reach up
to 130V. A fast switching diode with lower forward
voltage and higher reverse voltage (150V), such as
BAV20WS/BAS20W, can be used to enhance
efficiency.
Output Capacitor
Low ESR capacitors should be used at the regulated
boost output (CS pin) of the MIC4832 to minimize
the switching output ripple voltage. The larger the
output capacitance, the lower the output ripple at the
CS pin. The reduced output ripple at the CS pin
MIC4832
along with a low ESR capacitor improves the
efficiency of the MIC4832 circuit. Selection of the
capacitor value will depend upon the peak inductor
current, inductor size, and the load. The MIC4832 is
designed for use with an output capacitance as low
as 2.2nF. For minimum audible noise, the use of a
C0G/NPO dielectric output capacitor is
recommended. TDK and AVX offer C0G/NPO
dielectric capacitors in capacitances up to 2.7nF at
200V to 250V rating in 0805 size. If output ripple is a
concern a 0.01μF/200V X7R output capacitor is
recommended.
EL Lamp Terminals (VA, VB)
An EL lamp is connected from VA to VB as the load.
The high voltage alternated across VA and VB by
the H-Bridge cycles generate luminance. The
voltage at VA and VB should not exceed the voltage
at V CS by more than 3V. This situation may become
present when noisy enable signals such as those
often generated by mechanical switches are applied
to the driver’s inputs. To prevent over voltage at VA
and VB, 10k Ω resistors may be placed in series from
VA to the EL panel and from VB to the EL panel. An
alternative to the use of 10k Ω resistors is to apply a
diode from the CS pin to VA and VB, where the
cathode of the diode is on the CS side and the
anode is on the VA and VB side, respectively.
March 2009
7
M9999-033109-C
相关PDF资料 |
PDF描述 |
|---|---|
| TAJY686M016RNJ | CAP TANT 68UF 16V 20% 2917 |
| RSA40DRMT | CONN EDGECARD 80POS .125 SQ WW |
| RMA40DRMT | CONN EDGECARD 80POS .125 SQ WW |
| MC78M05BDTRK | IC REG LDO 5V .5A DPAK |
| ESC08DRYH-S13 | CONN EDGECARD 16POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC4832YMM TR | 功能描述:LED照明驱动器 220Vpp Low Noise EL Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MIC4833 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Low Noise Dual 220 VPP EL Driver With Output Voltage Slew Rate Control |
| MIC4833YML | 制造商:Micrel Inc 功能描述:EL Lamp DRVR 5.8V 12-Pin MLF 制造商:Micrel 功能描述:Low Noise 220Vp-p EL Driver MLF12 |
| MIC4833YML TR | 功能描述:LED照明驱动器 Dual EL Driver in 3x3MLF 12-Lead Package RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MIC4833YML-TR | 功能描述:IC DVR EL LOW NOISE 12-MLF 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 类型:EL 灯驱动器 频率:100Hz ~ 1.5kHz 电压 - 电源:2.3 V ~ 5.8 V 电流 - 电源:152μA 电流 - 灌/拉输出:- 调光:无 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:12-VFDFN 裸焊盘，12-MLF? 图号:* 制造商卷带直径:* 制造商卷带材料:* 制造商卷带宽度:* 供应商器件封装:12-MLF?（4x4） 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。