参数资料
| 型号： | MIC5200-3.0YS TR |
| 厂商： | Micrel Inc |
| 文件页数： | 8/10页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3V .1A SOT-223 |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3V |
| 输入电压： | 最高 26V |
| 电压 - 压降（标准）： | 0.23V @ 100mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 100mA |
| 电流 - 限制（最小）： | 100mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-261-4，TO-261AA |
| 供应商设备封装： | SOT-223 |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC5200-3.0YSTR MIC5200-3.0YSTR-ND |
MIC5200
Applications Information
External Capacitors
A 1μF capacitor is recommended between the MIC5200 output
and ground to prevent oscillations due to instability. Larger
values serve to improve the regulator ’s transient response.
Most types of tantalum or aluminum electrolytics will be ad-
equate; ?lm types will work, but are costly and therefore not
recommended. Many aluminum electrolytics have electrolytes
that freeze at about –30°C, so solid tantalum capacitors are
recommended for operation below –25°C. The important pa-
rameters of the capacitor are an effective series resistance
of about 5Ω or less and a resonant frequency above 500kHz.
The value of this capacitor may be increased without limit.
At lower values of output current, less output capacitance is
required for output stability. The capacitor can be reduced to
0.47μF for current below 10mA or 0.33μF for currents below
1 mA. A 1μF capacitor should be placed from the MIC5200
input to ground if there is more than 10 inches of wire between
the input and the AC ?lter capacitor or if a battery is used as
the input.
The MIC5200 will remain stable and in regulation with no load
in addition to the internal voltage divider, unlike many other
voltage regulators. This is especially important in CMOS RAM
keep-alive applications.
When used in dual supply systems where the regulator load
is returned to a negative supply, the output voltage must be
diode clamped to ground.
ENABLE Input
Micrel, Inc.
Thermal Considerations
Part I. Layout
The MIC5200-xxBM (8-pin surface mount package) has the
following thermal characteristics when mounted on a single
layer copper-clad printed circuit board.
PC Board θ JA
Dielectric
FR4 160°C/W
Ceramic 120°C/W
Multi-layer boards having a ground plane, wide traces near
the pads, and large supply bus lines provide better thermal
conductivity.
The “worst case” value of 160°C/W assumes no ground plane,
minimum trace widths, and a FR4 material board.
Part II. Nominal Power Dissipation and Die Temperature
The MIC5200-xxBM at a 25°C ambient temperature will oper-
ate reliably at up to 625mW power dissipation when mounted
in the “worst case” manner described above. At an ambient
temperature of 55°C, the device may safely dissipate 440mW.
These power levels are equivalent to a die temperature of
125°C, the recommended maximum temperature for non-
military grade silicon integrated circuits.
For MIC5200-xxBS (SOT-223 package) heat sink character-
istics, please refer to Micrel Application Hint 17, “Calculating
P.C. Board Heat Sink Area for Surface Mount Packages”.
50 mil
The MIC5200 features nearly zero OFF mode current. When
the ENABLE input is held below 0.7V, all internal circuitry is
powered off. Pulling this pin high (over 2.0V) re-enables the
device and allows operation. The ENABLE pin requires a small
amount of current, typically 15μA. While the logic threshold is
TTL/CMOS compatible, ENABLE may be pulled as high as
30V, independent of the voltage on V IN .
245 mil
30 mil
50 mil
150 mil
Minimum recommended board pad size, SO-8.
April 2005
8
M9999-040805
相关PDF资料 |
PDF描述 |
|---|---|
| AP130-25WL-7 | IC REG LDO 2.5V .3A SC59-3 |
| MIC5219YMM TR | IC REG LDO ADJ .5A 8-MSOP |
| GSC28DRTS-S93 | CONN EDGECARD 56POS DIP .100 SLD |
| MIC5219-5.0YMM TR | IC REG LDO 5V .5A 8-MSOP |
| MIC5219-3.6YMM TR | IC REG LDO 3.6V .5A 8-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC520033YS | 制造商:Micrel Inc 功能描述: |
| MIC5200-4.8BM | 功能描述:IC REG LDO 4.8V .1A 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC5200-4.8BM TR | 功能描述:IC REG LDO 4.8V .1A 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC5200-4.8BS | 功能描述:IC REG LDO 4.8V .1A SOT-223 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC5200-4.8BS TR | 功能描述:IC REG LDO 4.8V .1A SOT-223 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
发布紧急采购，3分钟左右您将得到回复。