- 您现在的位置：买卖IC网 > PDF目录13134 > MIC5201-3.3YS TR (Micrel Inc)IC REG LDO 3.3V .2A SOT223 PDF资料下载
参数资料
| 型号： | MIC5201-3.3YS TR |
| 厂商： | Micrel Inc |
| 文件页数： | 8/9页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V .2A SOT223 |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 最高 26V |
| 电压 - 压降（标准）： | 0.27V @ 200mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 200mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-261-4，TO-261AA |
| 供应商设备封装： | SOT-223 |
| 包装： | 标准包装 |
| 产品目录页面： | 1096 (CN2011-ZH PDF) |
| 其它名称： | 576-1251-6 |
MIC5201
Micrel, Inc.
Applications Information
V IN
MIC5201BM
V OUT
Figure 1 shows a basic fixed-voltage application with the
unused enable input connected to V IN .
IN
EN
OUT
ADJ
GND
R1
3.3 μ F
V IN
MIC5201-x.xBM
MIC5201-x.xBS
V OUT
R2
C ADJ
IN
EN
OUT
Figure 3. Decreasing Ouput Noise
GND
1 μ F
Minimum Load
The MIC5201 will remain stable and in regulation with no
Figure 1. Fixed Application
Adjustable regulators require two resistors to set the output
voltage. See Figure 2.
load unlike many other voltage regulators. This is
especially important in CMOS RAM keep-alive
applications.
V IN
MIC5201BM
IN OUT
V OUT
Dual-Supply Systems
When used in dual supply systems where the regulator
EN
ADJ
GND
R1
3.3 μ F
load is returned to a negative supply, the output voltage
must be diode clamped to ground.
V OUT = 1.242V ? 1 +
?
R1 ?
R2
? R2 ?
?
Figure 2. Adjustable Application
Resistors values are not critical because ADJ (adjust) has a
Thermal Considerations Layout
The MIC5201-x.xBM (8-pin surface mount package) has the
following thermal characteristics when mounted on a single
layer copper-clad printed circuit board.
high impedance, but for best results use resistors of 470k ?
or less.
Output Capacitors
A 1 μ F capacitor is recommended between the MIC5201
PC Board
Dielectric
FR4
Ceramic
θ JA
160oC/W
120oC/W
output and ground to prevent oscillations due to instability.
Larger values serve to improve the regulator’s transient
response. Most types of tantalum or aluminum electrolytics
will be adequate; film types will work, but are costly and
therefore not recommended. Many aluminum electrolytics
have electrolytes that freeze at about –30 ° C, so solid tanta-
lums are recommended for operation below –25 ° C. The
important parameters of the capacitor are an effective series
resistance of about 5 ? or less and a resonant frequency
above 500kHz. The value of this capacitor may be increased
without limit.
At lower values of output current, less output capacitance is
required for output stability. The capacitor can be reduced to
0.47 μ F for current below 10mA or 0.33 μ F for currents below
1mA.
Input Capacitors
A 1 μ F capacitor should be placed from the MIC5201 input to
ground if there is more than 10 inches of wire between the
input and the ac filter capacitor or if a battery is used as the
input.
Noise Reduction Capacitors
On adjustable devices, a capacitor from ADJ to GND will
Multilayer boards having a ground plane, wide traces near the
pads, and large supply bus lines provide better thermal
conductivity.
The “worst case” value of 160 ° C/W assumes no ground
plane, minimum trace widths, and a FR4 material board.
Nominal Power Dissipation and Die Temperature
The MIC5201-x.xBM at a 25 ° C ambient temperature will
operate reliably at up to 625mW power dissipation when
mounted in the “worst case” manner described above. At an
ambient temperature of 55 ° C, the device may safely dissi-
pate 440mW. These power levels are equivalent to a die
temperature of 125 ° C, the recommended maximum tem-
perature for non-military grade silicon integrated circuits.
For MIC5201-x.xBS (SOT-223 package) heat sink character-
istics, please refer to Micrel Application Hint 17, P.C. Board
Heat Sinking .
50 mil
decrease high-frequency noise on the output. See Figure 3.
245 mil
30 mil
50 mil
150 mil
Figure 4. Min. Recommended SO-8 PCB Pads Size
MIC5201
8
June 2005
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J6K-CX | CONVERTER MOD DC/DC 40V 75W |
| RCB64DHND | CONN EDGECARD 128PS DIP .050 SLD |
| RMM28DRST | CONN EDGECARD 56POS DIP .156 SLD |
| RBA31DRMD | CONN EDGECARD 62POS .125 SQ WW |
| VE-B1K-EU-F1 | CONVERTER MOD DC/DC 40V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5201-4.8BM | 功能描述:IC REG LDO 4.8V .2A 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC5201-4.8BM TR | 功能描述:IC REG LDO 4.8V .2A 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC5201-4.8BS | 功能描述:IC REG LDO 4.8V .2A SOT223 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC5201-4.8BS TR | 功能描述:IC REG LDO 4.8V .2A SOT-223 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC5201-4.8YM | 功能描述:低压差稳压器 - LDO 200mA, 1% LDO Regulator (Lead Free) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。