- 您现在的位置：买卖IC网 > PDF目录13262 > MIC5207-3.3YM5 TR (Micrel Inc)IC REG LDO 3.3V .18A SOT23-5 PDF资料下载
参数资料
| 型号： | MIC5207-3.3YM5 TR |
| 厂商： | Micrel Inc |
| 文件页数： | 10/13页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V .18A SOT23-5 |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 最高 16V |
| 电压 - 压降（标准）： | 0.165V @ 150mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 180mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 标准包装 |
| 产品目录页面： | 1097 (CN2011-ZH PDF) |
| 其它名称： | 576-1267-6 |
Micrel, Inc.
V IN(MAX) = 6.01V
Therefore, a 3.3V application at 150mA of output current
can accept a maximum input voltage of 6V in a SOT-23-
5 package. For a full discussion of heat sinking and
thermal effects on voltage regulators, refer to the
Regulator Thermals section of Micrel’s Designing with
Low-Dropout Voltage Regulators handbook
MIC5207
Figure 2. Low-Noise Fixed Voltage Application
Low-Voltage Operation
Figure 2 is an example of a
basic
low-noise
The MIC5207-1.8 and MIC5207-2.5 require special
consideration when used in voltage-sensitive systems.
They may momentarily overshoot their nominal output
voltages unless appropriate output and bypass capacitor
values are chosen.
During regulator power up, the pass transistor is fully
saturated for a short time, while the error amplifier and
configuration. C OUT = 1μF minimum.
Adjustable Regulator Applications
The MIC5207BM5 can be adjusted to a specific output
voltage by using two external resistors (Figure 3). The
resistors set the output voltage based on the following
equation:
V OUT = V REF ? 1 +
? , V REF = 1.242V
voltage reference are being powered up more slowly
from the output (see “Block Diagram”). Selecting larger
output and bypass capacitors allows additional time for
?
?
R2 ?
R1 ?
the error amplifier and reference to turn on and prevent
overshoot.
To ensure that no overshoot is present when starting up
into a light load (100μA), use a 4.7μF output capacitance
and 470pF bypass capacitance. This slows the turn-on
enough to allow the regulator to react and keep the
output voltage from exceeding its nominal value. At
heavier loads, use a 10μF output capacitance and
470pF bypass capacitance. Lower values of output and
bypass capacitance can be used, depending on the
sensitivity of the system.
Applications that can withstand some overshoot on the
output of the regulator can reduce the output capacitor
and/or reduce or eliminate the bypass capacitor.
Applications that are not sensitive to overshoot due to
power-on reset delays can use normal output and
bypass capacitor configurations.
Please note the junction temperature range of the
regulator at 1.8V output (fixed and adjustable) is 0 ? C to
+125 ? C.
Fixed Regulator Applications
Figure 1. Ultra-Low-Noise Fixed Voltage Application
Figure 1 includes a 470pF capacitor for ultra-low-noise
operation and shows EN (pin 3) connected to IN (pin 1)
for an application where enable/shutdown is not
required. C OUT = 2.2μF minimum.
This equation is correct due to the configuration of the
bandgap reference. The bandgap voltage is relative to
the output, as seen in the block diagram. Traditional
regulators normally have the reference voltage relative
to ground; therefore, their equations are different from
the equation for the MIC5207BM5.
Resistor values are not critical because ADJ (adjust) has
a high input impedance, but for best results use resistors
of 470k ? or less. A capacitor from ADJ to ground
provides greatly improved noise performance.
Figure 3. Ultra-Low-Noise Adjustable Voltage Application
Figure 3 includes the optional 470pF noise bypass
capacitor from ADJ to GND to reduce output noise.
Dual-Supply Operation
When used in dual-supply systems where the regulator
load is returned to a negative supply, the output voltage
must be diode clamped to ground.
USB Application
Figure 4 shows the MIC5207-3.3BZ (3-terminal, TO-92)
in a USB application. Since the V BUS supply may be
greater than 10 inches from the regulator, a 1μF input
capacitor is included.
December 2007
10
M9999-123107
相关PDF资料 |
PDF描述 |
|---|---|
| MAX814KEPA+ | IC SUPERVISOR MPU LP 8-DIP |
| GBB60DHHT | CONN EDGECARD 120PS .050 DIP SLD |
| EEU-FR1J181B | CAP ALUM 180UF 63V 20% RADIAL |
| MAX814NEPA+ | IC SUPERVISOR MPU LP 8-DIP |
| 400SXW33MEFC16X25 | CAP ALUM 33UF 400V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5207-4.0BM5 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MIC5207-4.0BM5 TR | 功能描述:IC REG LDO 4V .18A SOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:500 系列:- 稳压器拓扑结构:正，固定式 输出电压:12V 输入电压:14.5 V ~ 35 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:500mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:TO-205AD，TO-39-3 金属罐 供应商设备封装:TO-39 包装:散装 其它名称:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
| MIC5207-4.0BM5TR | 制造商:RF Micro Devices Inc 功能描述: |
| MIC5207-4.0YM5 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:180mA Low-Noise LDO Regulator |
| MIC5207-4.0YM5 TR | 功能描述:低压差稳压器 - LDO 180mA 3% Low Noise LDO(Lead Free) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。