参数资料
| 型号： | MIC5209-4.2YS TR |
| 厂商： | Micrel Inc |
| 文件页数： | 10/13页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 4.2V .5A SOT-223 |
| 标准包装： | 2,500 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 4.2V |
| 输入电压： | 最高 16V |
| 电压 - 压降（标准）： | 0.35V @ 500mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 500mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-261-4，TO-261AA |
| 供应商设备封装： | SOT-223 |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC5209-4.2YSTR MIC5209-4.2YSTR-ND |
MIC5209
Micrel, Inc.
V IN
I N
OUT
EN
BYP
IN
OUT
EN
ADJ
FixedRegulatorCircuits
MIC5209-x.xBM
2 3
1 4
GND
5–8
V OUT
1μF
V IN
2
1
MIC5209BM
3
4
GND
5–8
470pF
R1
R2
V OUT
2.2μF
V IN
V OUT
I N
OUT
E N
BYP
470pF
V IN
V OUT
I N
OUT
R1
E N
ADJ
V IN
V OUT
I N
OUT
C IN
C OUT
0.1μF 22μF
R2
V OUT = 1.242V ? 1 +
? R2 ?
R1 ?
?
Figure1. Low-NoiseFixedVoltageRegulator
Figure 1 shows a basic MIC5209-x.xBM (SO-8) ? xed-voltage
regulator circuit. See Figure 5 for a similar con? guration us-
ing the more thermally-ef? cient MIC5209-x.xBS (SOT-223).
A 1μF minimum output capacitor is required for basic ? xed-
voltage applications.
MIC5209-x.xBM
2 3
1 4
GND 2.2μF
5–8
Figure 2. Ultra-Low-Noise Fixed Voltage Regulator
Figure 2 includes the optional 470pF noise bypass capacitor
between BYP and GND to reduce output noise. Note that the
minimum value of C OUT must be increased when the bypass
capacitor is used.
Adjustable Regulator Circuits
MIC5209BM
2 3
1 4
GND 1μF
5–8
Figure 3. Low-Noise Adjustable Voltage Regulator
The MIC5209BM/U can be adjusted to a speci? c output volt-
age by using two external resistors (Figure 3). The resistors
set the output voltage based on the equation:
?
This equation is correct due to the con? guration of the
bandgap reference. The bandgap voltage is relative to the
output, as seen in the block diagram. Traditional regula-
tors normally have the reference voltage relative to ground;
therefore, their equations are different from the equation for
the MIC5209BM/U.
Although ADJ is a high-impedance input, for best performance,
R2 should not exceed 470kΩ.
Figure 4. Ultra-Low-Noise Adjustable Application.
Figure 4 includes the optional 470pF bypass capacitor from
ADJ to GND to reduce output noise.
Slot-1 Power Supply
Intel’s Pentium II processors have a requirement for a 2.5V
±5% power supply for a clock synthesizer and its associated
loads. The current requirement for the 2.5V supply is depen-
dant upon the clock synthesizer used, the number of clock
outputs, and the type of level shifter (from core logic levels to
2.5V levels). Intel estimates a worst-case load of 320mA.
The MIC5209 was designed to provide the 2.5V power
requirement for Slot-1 applications. Its guaranteed perfor-
mance of 2.5V ±3% at 500mA allows adequate margin for
all systems, and its dropout voltage of 500mV means that it
operates from a worst-case 3.3V supply where the voltage
can be as low as 3.0V.
MIC5209-x.xBS
1 3
GND
2,TAB
Figure 5. Slot-1 Power Supply
A Slot-1 power supply (Figure 5) is easy to implement. Only
two capacitors are necessary, and their values are not criti-
cal. C IN bypasses the internal circuitry and should be at least
0.1μF. C OUT provides output ? ltering, improves transient
response, and compensates the internal regulator control
loop. Its value should be at least 22μF. C IN and C OUT may
be increased as much as desired.
Slot-1 Power Supply Power Dissipation
Powered from a 3.3V supply, the Slot-1 power supply of
Figure 5 has a nominal ef? ciency of 75%. At the maximum
anticipated Slot 1 load (320mA), the nominal power dissipa-
tion is only 256mW.
The SOT-223 package has suf? cient thermal characteristics
for wide design margins when mounted on a single layer
copper-clad printed circuit board. The power dissipation of
the MIC5209 is calculated using the voltage drop across the
device × output current plus supply voltage × ground current.
M9999-060906
10
June 2006
相关PDF资料 |
PDF描述 |
|---|---|
| AP1117D15G-13 | IC REG LDO 1.5V 1A TO252-3 |
| EMA40DTKT-S288 | CONN EDGECARD 80POS .125 EXTEND |
| ABM24DTKT-S288 | CONN EDGECARD EXTEND 48POS .156 |
| AMM08DTMI | CONN EDGECARD 16POS R/A .156 SLD |
| GSM43DSEI-S243 | CONN EDGECARD 86POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5209-5.0BM | 功能描述:IC REG LDO 5V .5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC5209-5.0BM TR | 功能描述:IC REG LDO 5V .5A 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC5209-5.0BS | 功能描述:IC REG LDO 5V .5A SOT223 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
| MIC5209-5.0BS TR | 功能描述:IC REG LDO 5V .5A SOT-223 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:500 系列:- 稳压器拓扑结构:正，固定式 输出电压:12V 输入电压:14.5 V ~ 35 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:500mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:TO-205AD，TO-39-3 金属罐 供应商设备封装:TO-39 包装:散装 其它名称:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
| MIC5209-5.0BU | 功能描述:IC REG LDO 5V .5A TO263-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.8V 输入电压:最高 16V 电压 - 压降（标准）:0.3V @ 80mA 稳压器数量:1 电流 - 输出:80mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
发布紧急采购，3分钟左右您将得到回复。