参数资料
| 型号： | MIC5211-3.3YM6 TR |
| 厂商： | Micrel Inc |
| 文件页数： | 3/9页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V 50MA SOT23-6 |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 2.5 V ~ 16 V |
| 电压 - 压降（标准）： | 0.25V @ 50mA |
| 稳压器数量： | 2 |
| 电流 - 输出： | 50mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-23-6 |
| 包装： | 标准包装 |
| 产品目录页面： | 1097 (CN2011-ZH PDF) |
| 其它名称： | 576-2748-6 |
MIC5211
Absolute Maximum Ratings (Note 1)
Supply Input Voltage (V IN ) ..............................–20V to +20V
Enable Input Voltage (V EN ) ............................–20V to +20V
Power Dissipation (P D ) ............................. Internally Limited
Storage Temperature Range .................... –60°C to +150°C
Lead Temperature (soldering, 5 sec.) ........................ 260°C
ESD, (Note 3) ......................................................................
Micrel, Inc.
Operating Ratings (Note 2)
Supply Input Voltage (V IN ) .................................2.5V to 16V
Enable Input Voltage (V EN ) ..................................0V to 16V
Junction Temperature (T J ) (except 1.8V) .. –40°C to +125°C
1.8V only ................................................... 0°C to +125°C
6-lead SOT-23-6 (θ JA ) ............................................. Note 4
Electrical Characteristics
V IN = V OUT + 1V; I L = 1mA; C L = 0.1μF, and V EN ≥ 2.0V; T J = 25°C, bold values indicate –40°C to +125°C;
for one-half of dual MIC5211; unless noted.
Symbol
V O
ΔV O /ΔT
ppm/°C
ΔV O /V O
ΔV O /V O
V IN – V O
I Q
I GND
I LIMIT
ΔV O /ΔP D
Enable Input
V IL
V IH
I IL
I IH
Parameter
Output Voltage
Accuracy
Output Voltage
Temperature Coeffcient
Line Regulation
Load Regulation
Dropout Voltage, Note 7
Quiescent Current
Ground Pin Current
Note 8
Current Limit
Thermal Regulation
Enable Input Voltage Level
Enable Input Current
Conditions
variation from nominal V OUT
Note 5
V IN = V OUT +1V to 16V
I L = 0.1mA to 50mA, Note 6
I L = 100μA
I L = 20mA
I L = 50mA
V EN ≤ 0.4V (shutdown)
V EN ≥ 2.0V, I L = 100μA (active)
I L = 20mA (active)
I L = 50mA (active)
V OUT = 0V
Note 9
logic low (off)
logic high (on)
V IL ≤ 0.6V
V IH ≥ 2.0V
Min
–3
–4
2.0
Typical
50
0.008
0.08
20
200
250
0.01
90
225
750
140
0.05
0.01
3
Max
3
4
200
0.3
0.5
0.3
0.5
450
500
10
450
1200
250
0.6
1
50
Units
%
%
%
%
%
%
mV
mV
mV
μA
μA
μA
μA
mA
%/W
V
V
μA
μA
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
Note 9:
Exceeding the absolute maximum rating may damage the device.
The device is not guareented to function outside itsperating rating.
Devices are ESD sensitive. Handling precautions recommended.
The maximum allowable power dissipation at any T A (ambient temperature) is P D(max) = (T J(max) – T A ) / θ JA . Exceeding the maximum allow-
able power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. The θ JA is 220°C/W for the
SOT-23-6 mounted on a printed circuit board.
Output voltage temperature coef?ecient is de?ned as the worst case voltage change divided by the total temperature range.
Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load
range from 0.1mA to 50mA. Change in output voltage due to heating effects are covered by thermal regulation speci?cation.
Dropout voltage is de?ned as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V
differential. For output voltages below 2.5V, dropout voltage is the input-to-output voltage differential with the minimum voltage being 2.5V.
Minimum input opertating voltage is 2.5V.
Ground pin current is the quiescent current per regulator plus pass transistor base current. The total current drawn from the supply is the sum
of the load current plus the ground pin current.
Thermal regulation is de?ned as the change in output voltage at a time “t” after a change in power dissipation is applied, excluding load or line
regulation effects. Speci?cations are for a 50mA load pulse at V IN = 16V for t = 10ms.
May 2006
3
MIC5211
相关PDF资料 |
PDF描述 |
|---|---|
| MIC5212-SJBM TR | IC REG LDO 3.3V/2.5V .5A 8-SOIC |
| MIC5213-2.5YC5 TR | IC REG LDO 2.5V 80MA SC70-5 |
| MIC5216-3.3YM5 TR | IC REG LDO 3.3V .5A SOT23-5 |
| MIC5219-5.0YMT TR | IC REG LDO 5V .5A 6-TMLF |
| MIC5225-2.7YM5 TR | IC REG LDO 2.7V .15A SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5211-5.0BM6 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MIC5211-5.0BM6 TR | 功能描述:IC REG LDO 5V 50MA SOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:500 系列:- 稳压器拓扑结构:正，固定式 输出电压:12V 输入电压:14.5 V ~ 35 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:500mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:TO-205AD，TO-39-3 金属罐 供应商设备封装:TO-39 包装:散装 其它名称:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
| MIC5211-5.0BM6TR | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| MIC5211-5.0YM6 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Dual μCap 80mA LDO Regulator |
| MIC5211-BCYM6 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Dual μCap 80mA LDO Regulator |
发布紧急采购，3分钟左右您将得到回复。