参数资料
| 型号： | MIC5211-BLYM6 TR |
| 厂商： | Micrel Inc |
| 文件页数： | 7/9页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.8/3.3V 50MA SOT23-6 |
| 标准包装： | 3,000 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.8V，3.3V |
| 输入电压： | 2.5 V ~ 16 V |
| 电压 - 压降（标准）： | 0.25V @ 50mA |
| 稳压器数量： | 2 |
| 电流 - 输出： | 50mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-23-6 |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC5211-BLYM6TR MIC5211-BLYM6TR-ND |
MIC5211
Micrel, Inc.
Applications Information
Enable/Shutdown
P D(max) =
T J(max) – T A
θ JA
P D(max) =
θ JA
P D(max) =
ENAand ENB (enable/shutdown) may be controlled sepa-
rately. Forcing ENA/B high (>2V) enables the regulator. The
enable inputs typically draw only 15μA.
While the logic threshold is TTL/CMOS compatible, ENA/B
may be forced as high as 20V, independent of V IN . ENA/B may
be connected to the supply if the function is not required.
Input Capacitor
A 0.1μF capacitor should be placed from IN to GND if there
is more than 10 inches of wire between the input and the ac
?lter capacitor or when a battery is used as the input.
Output Capacitor
Typical PNP based regulators require an output capacitor
to prevent oscillation. The MIC5211 is ultrastable, requiring
only 0.1μF of output capacitance per regulator for stability.
The regulator is stable with all types of capacitors, includ-
ing the tiny, low-ESR ceramic chip capacitors. The output
capacitor value can be increased without limit to improve
transient response.
The capacitor should have a resonant frequency above
500kHz. Ceramic capacitors work, but some dielectrics have
poor temperature coef?cients, which will affect the value of
the output capacitor over temperature. Tantalum capacitors
are much more stable over temperature, but typically are
larger and more expensive. Aluminum electrolytic capacitors
will also work, but they have electrolytes that freeze at about
–30°C. Tantalum or ceramic capacitors are recommended
for operation below –25°C.
No-Load Stability
The MIC5211 will remain stable and in regulation with no load
(other than the internal voltage divider) unlike many other
voltage regulators. This is especially important in CMOS
RAM keep-alive applications.
Thermal Shutdown
Thermal shutdown is independent on both halves of the dual
MIC5211, however, an overtemperature condition in one half
may affect the other half because of proximity.
Thermal Considerations
When designing with a dual low-dropout regulator, both sec-
tions must be considered for proper operation. The part is
designed with thermal shutdown, therefore, the maximum
junction temperature must not be exceeded. Since the dual
regulators share the same substrate, the total power dissipa-
tion must be considered to avoid thermal shutdown. Simple
thermal calculations based on the power dissipation of both
regulators will allow the user to determine the conditions for
proper operation.
The maximum power dissipation for the total regulator system
can be determined using the operating temperatures and the
thermal resistance of the package. In a minimum footprint
con?guration, the SOT-23-6 junction-to-ambient thermal
resistance (θ JA ) is 220°C/W. Since the maximum junction
temperature for this device is 125°C, at an operating tem-
perature of 25°C the maximum power dissipation is:
125°C – 25°C
220°C/W
P D(max) = 455mW
The MIC5211-3.0 can supply 3V to two different loads indepen-
dently from the same supply voltage. If one of the regulators
is supplying 50mA at 3V from an input voltage of 4V, the total
power dissipation in this portion of the regulator is:
P D1 = (V IN – V OUT ) I OUT + V IN ? I GND
P D1 = (4V – 3V) 50mA + 4V ? 0.85mA
P D1 = 53.4mW
Up to approximately 400mW can be dissipated by the remain-
ing regulator (455mW – 53.4mW) before reaching the thermal
shutdown temperature, allowing up to 50mA of current.
P D2 = (V IN – V OUT ) I OUT + V IN ? I GND
P D2 = (4V – 3V) 50mA + 4V ? 0.85mA
P D2 = 53.4mW
The total power dissipation is:
P D1 + P D2 = 53.4mW + 53.4mW
P D1 + P D2 = 106.8mW
Therefore, with a supply voltage of 4V, both outputs can oper-
ate safely at room temperature and full load (50mA).
V IN
MIC5211
IN OUTA V OUTA
ENA O UTB V OU TB
ENB GND
1μF 1μF
Figure 1. Thermal Conditions Circuit
In many applications, the ambient temperature is much higher.
By recalculating the maximum power dissipation at 70°C
ambient, it can be determined if both outputs can supply full
load when powered by a 4V supply.
T J(max) – T A
P D(max) =
125°C – 70°C
220°C/W
P D(max) = 250mW
At 70°C, the device can provide 250mW of power dissipation,
suitable for the above application.
When using supply voltages higher than 4V, do not exceed
the maximum power dissipation for the device. If the device is
operating from a 7.2V-nominal two-cell lithium-ion battery and
May 2006
7
MIC5211
相关PDF资料 |
PDF描述 |
|---|---|
| MIC5211-BCYM6 TR | IC REG LDO 1.8/2.5V 50MA SOT23-6 |
| RMA31DRMD-S288 | CONN EDGECARD 62POS .125 EXTEND |
| GMM31DTBN | CONN EDGECARD 62POS R/A .156 SLD |
| RSM30DTKT | CONN EDGECARD 60POS DIP .156 SLD |
| GSM31DTBH | CONN EDGECARD 62POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5211-CLYM6 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Dual μCap 80mA LDO Regulator |
| MIC5211-CLYM6 TR | 功能描述:低压差稳压器 - LDO MIC5211-2.5/3.3YM6 Dual Cap 50mA LDO (Lead Free) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC5211-LXYM6 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Dual μCap 80mA LDO Regulator |
| MIC5211-LXYM6 TR | 功能描述:低压差稳压器 - LDO MIC5211-3.3/5.0YM6 Dual Cap 50mA LDO (Lead Free) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC5211-LXYM6-TR | 功能描述:Linear Voltage Regulator IC Positive Fixed 2 Output 3.3V, 5V 80mA SOT-23-6 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:有效 稳压器拓扑:正，固定式 电压 - 输出:3.3V，5V 电流 - 输出:80mA 电压 - 跌落（典型值）:0.25V @ 50mA 稳压器数:2 电压 - 输入:2.5 V ~ 16 V 电流 - 限制（最小值）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商器件封装:SOT-23-6 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。