- 您现在的位置：买卖IC网 > PDF目录13091 > MIC5219-3.3YMM (Micrel Inc)IC REG LDO 3.3V .5A 8-MSOP PDF资料下载
参数资料
| 型号： | MIC5219-3.3YMM |
| 厂商： | Micrel Inc |
| 文件页数： | 9/14页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.3V .5A 8-MSOP |
| 标准包装： | 100 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.3V |
| 输入电压： | 最高 12V |
| 电压 - 压降（标准）： | 0.35V @ 500mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 500mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
| 产品目录页面： | 1098 (CN2011-ZH PDF) |
| 其它名称： | 576-1827-5 MIC5219-3.3YMM-ND |
( T J ( max ) ? T A )
θ JA
( 125 ° C ? 25 ° C )
P D ( max ) =
Micrel, Inc.
Applications Information
The MIC5219 is designed for 150mA to 200mA output current
applications where a high current spike (500mA) is needed for
short, start-up conditions. Basic application of the device will
be discussed initially followed by a more detailed discussion
of higher current applications.
Enable/Shutdown
Forcing EN (enable/shutdown) high (>2V) enables the
regulator. EN is compatible with CMOS logic. If the enable/
shutdown feature is not required, connect EN to IN (supply
input). See Figure 5.
Input Capacitor
A 1μF capacitor should be placed from IN to GND if there is
more than 10 inches of wire between the input and the AC
filter capacitor or if a battery is used as the input.
Output Capacitor
An output capacitor is required between OUT and GND to
prevent oscillation. The minimum size of the output capacitor
is dependent upon whether a reference bypass capacitor is
used. 1μF minimum is recommended when C BYP is not used
(see Figure 5). 2.2μF minimum is recommended when C BYP
is 470pF (see Figure 6). For applications < 3V, the output
capacitor should be increased to 22μF minimum to reduce
start-up overshoot. Larger values improve the regulator ’s
transient response. The output capacitor value may be in -
creased without limit.
The output capacitor should have an ESR (equivalent series
resistance) of about 1Ω or less and a resonant frequency
above 1MHz. Ultra-low-ESR capacitors could cause oscilla -
tion and/or underdamped transient response. Most tantalum
or aluminum electrolytic capacitors are adequate; film types
will work, but are more expensive. Many aluminum electro -
lytics have electrolytes that freeze at about –30°C, so solid
tantalums are recommended for operation below –25°C.
At lower values of output current, less output capacitance is
needed for stability. The capacitor can be reduced to 0.47μF
for current below 10mA, or 0.33μF for currents below 1mA.
No-Load Stability
The MIC5219 will remain stable and in regulation with no load
(other than the internal voltage divider) unlike many other
voltage regulators. This is especially important in CMOS
RAM keep-alive applications.
Reference Bypass Capacitor
BYP is connected to the internal voltage reference. A 470pF
capacitor (C BYP ) connected from BYP to GND quiets this
reference, providing a significant reduction in output noise
(ultra-low-noise performance). C BYP reduces the regulator
phase margin; when using C BYP , output capacitors of 2.2μF
or greater are generally required to maintain stability.
The start-up speed of the MIC5219 is inversely proportional
to the size of the reference bypass capacitor. Applications
requiring a slow ramp-up of output voltage should consider
larger values of C BYP . Likewise, if rapid turn-on is necessary,
consider omitting C BYP .
MIC5219
Thermal Considerations
The MIC5219 is designed to provide 200mA of continuous
current in two very small profile packages. Maximum power
dissipation can be calculated based on the output current and
the voltage drop across the part. To determine the maximum
power dissipation of the package, use the thermal resistance,
junction-to-ambient, of the device and the following basic
equation.
P D ( max ) =
T J (max) is the maximum junction temperature of the die,
125°C, and T A is the ambient operating temperature. θ JA
is layout dependent; Table 1 shows examples of thermal
resistance, junction-to-ambient, for the MIC5219.
Package θ JA Recommended θ JA 1" Square θ JC
Minimum Footprint 2oz. Copper
MM8 ? (MM) 160°C/W 70°C/W 30°C/W
SOT-23-5 (M5) 220°C/W 170°C/W 130°C/W
2 × 2 MLF ? (ML) 90°C/W — —
2 × 2 Thin
MLF ? (MT) 90°C/W — —
Table 1. MIC5219 Thermal Resistance
The actual power dissipation of the regulator circuit can be
determined using one simple equation.
P D = (V IN – V OUT ) I OUT + V IN I GND
Substituting P D (max) for P D and solving for the operating
conditions that are critical to the application will give the
maximum operating conditions for the regulator circuit. For
example, if we are operating the MIC5219-3.3BM5 at room
temperature, with a minimum footprint layout, we can deter -
mine the maximum input voltage for a set output current.
220 ° C / W
P D (max) = 455mW
The thermal resistance, junction-to-ambient, for the minimum
footprint is 220°C/W, taken from Table 1. The maximum power
dissipation number cannot be exceeded for proper opera -
tion of the device. Using the output voltage of 3.3V, and an
output current of 150mA, we can determine the maximum
input voltage. Ground current, maximum of 3mA for 150mA
of output current, can be taken from the “Electrical Charac -
teristics” section of the data sheet.
455mW = (V IN – 3.3V) × 150mA + V IN × 3mA
455mW = (150mA) × V IN + 3mA × V IN – 495mW
950mW = 153mA × V IN
V IN = 6.2V MAX
Therefore, a 3.3V application at 150mA of output current
can accept a maximum input voltage of 6.2V in a SOT-23-5
package. For a full discussion of heat sinking and thermal
effects on voltage regulators, refer to the “Regulator Ther -
mals” section of Micrel’s Designing with Low-Dropout Voltage
Regulators handbook.
June 2009
9
M0371-061809
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B3B-EY-F2 | CONVERTER MOD DC/DC 95V 50W |
| RYM08DRMT-S664 | CONN EDGECARD 16POS .156 WW |
| VE-B3B-EX-S | CONVERTER MOD DC/DC 95V 75W |
| VI-J7V-CZ-B1 | CONVERTER MOD DC/DC 5.8V 25W |
| VE-J1D-EZ-B1 | CONVERTER MOD DC/DC 85V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5219-5.0BM5 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:500mA-Peak Output LDO Regulator |
| MIC5219-5.0BM5 TR | 功能描述:IC REG LDO 5V .5A SOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:500 系列:- 稳压器拓扑结构:正，固定式 输出电压:12V 输入电压:14.5 V ~ 35 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:500mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:TO-205AD，TO-39-3 金属罐 供应商设备封装:TO-39 包装:散装 其它名称:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
| MIC5219-5.0BM5TR | 制造商:RF Micro Devices Inc 功能描述: 制造商:Micrel Inc 功能描述: |
| MIC5219-5.0BMM | 功能描述:IC REG LDO 5V .5A 8-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:500 系列:- 稳压器拓扑结构:正，固定式 输出电压:12V 输入电压:14.5 V ~ 35 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:500mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:TO-205AD，TO-39-3 金属罐 供应商设备封装:TO-39 包装:散装 其它名称:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
| MIC5219-5.0BMM TR | 功能描述:IC REG LDO 5V .5A 8-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:500 系列:- 稳压器拓扑结构:正，固定式 输出电压:12V 输入电压:14.5 V ~ 35 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:500mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:TO-205AD，TO-39-3 金属罐 供应商设备封装:TO-39 包装:散装 其它名称:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
发布紧急采购，3分钟左右您将得到回复。