- 您现在的位置：买卖IC网 > PDF目录13093 > MIC5219YMM (Micrel Inc)IC REG LDO ADJ .5A 8-MSOP PDF资料下载
参数资料
| 型号： | MIC5219YMM |
| 厂商： | Micrel Inc |
| 文件页数： | 10/14页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ .5A 8-MSOP |
| 标准包装： | 100 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 可调 |
| 输入电压： | 2.5 V ~ 12 V |
| 电压 - 压降（标准）： | 0.35V @ 500mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 500mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
| 产品目录页面： | 1098 (CN2011-ZH PDF) |
| 其它名称： | 576-3437 MIC5219YMM-ND |
( T J ( max ) ? T A )
θ JA
( 125 ° C ? 25 ° C )
P D ( max ) =
(
)
Avg.P D = ?
? V IN – V OUT I OUT + V IN I GND
V IN ( max ) =
= 5 . 683V
? ( 8V – 5V ) 500mA + 8V × 20mA
? % DC ?
? 100 ?
? % Duty Cycle ?
?
?
455mW = ? ? 1.66W
0.274 =
Micrel, Inc.
Peak Current Applications
The MIC5219 is designed for applications where high start-up
currents are demanded from space constrained regulators.
This device will deliver 500mA start-up current from a SOT-
23-5 or MM8 package, allowing high power from a very low
profile device. The MIC5219 can subsequently provide output
current that is only limited by the thermal characteristics of
the device. You can obtain higher continuous currents from
the device with the proper design. This is easily proved with
some thermal calculations.
If we look at a specific example, it may be easier to follow.
The MIC5219 can be used to provide up to 500mA continuous
output current. First, calculate the maximum power dissipa -
tion of the device, as was done in the thermal considerations
section. Worst case thermal resistance ( θ JA = 220°C/W for
the MIC5219-x.xBM5), will be used for this example.
P D ( max ) =
Assuming a 25°C room temperature, we have a maximum
power dissipation number of
220 ° C / W
P D (max) = 455mW
Then we can determine the maximum input voltage for a
5-volt regulator operating at 500mA, using worst case ground
current.
P D (max) = 455mW = (V IN – V OUT ) I OUT + V IN I GND
I OUT = 500mA
V OUT = 5V
I GND = 20mA
455mW = (V IN – 5V) 500mA + V IN × 20mA
2.995W = 520mA × V IN
2 . 955W
520mA
Therefore, to be able to obtain a constant 500mA output cur -
rent from the 5219-5.0BM5 at room temperature, you need
extremely tight input-output voltage differential, barely above
the maximum dropout voltage for that current rating.
You can run the part from larger supply voltages if the proper
precautions are taken. Varying the duty cycle using the en -
able pin can increase the power dissipation of the device by
maintaining a lower average power figure. This is ideal for
applications where high current is only needed in short bursts.
Figure 1 shows the safe operating regions for the MIC5219-x.
xBM5 at three different ambient temperatures and at differ -
ent output currents. The data used to determine this figure
assumed a minimum footprint PCB design for minimum heat
sinking. Figure 2 incorporates the same factors as the first
figure, but assumes a much better heat sink. A 1" square cop -
per trace on the PC board reduces the thermal resistance of
the device. This improved thermal resistance improves power
dissipation and allows for a larger safe operating region.
Figures 3 and 4 show safe operating regions for the MIC5219-x.
MIC5219
xBMM, the power MSOP package part. These graphs show
three typical operating regions at different temperatures. The
lower the temperature, the larger the operating region. The
graphs were obtained in a similar way to the graphs for the
MIC5219-x.xBM5, taking all factors into consideration and
using two different board layouts, minimum footprint and 1"
square copper PC board heat sink. (For further discussion
of PC board heat sink characteristics, refer to “Application
Hint 17, Designing PC Board Heat Sinks” .)
The information used to determine the safe operating regions
can be obtained in a similar manner such as determining
typical power dissipation, already discussed. Determining
the maximum power dissipation based on the layout is the
first step, this is done in the same manner as in the previous
two sections. Then, a larger power dissipation number multi -
plied by a set maximum duty cycle would give that maximum
power dissipation number for the layout. This is best shown
through an example. If the application calls for 5V at 500mA
for short pulses, but the only supply voltage available is
8V, then the duty cycle has to be adjusted to determine an
average power that does not exceed the maximum power
dissipation for the layout.
? % DC ?
? 100 ?
455mW = ?
100
% Duty Cycle
100
% Duty Cycle Max = 27.4%
With an output current of 500mA and a three-volt drop across
the MIC5219-xxBMM, the maximum duty cycle is 27.4%.
Applications also call for a set nominal current output with a
greater amount of current needed for short durations. This is a
tricky situation, but it is easily remedied. Calculate the average
power dissipation for each current section, then add the two
numbers giving the total power dissipation for the regulator.
For example, if the regulator is operating normally at 50mA,
but for 12.5% of the time it operates at 500mA output, the
total power dissipation of the part can be easily determined.
First, calculate the power dissipation of the device at 50mA.
We will use the MIC5219-3.3BM5 with 5V input voltage as
our example.
P D × 50mA = (5V – 3.3V) × 50mA + 5V × 650μA
P D × 50mA = 173mW
However, this is continuous power dissipation, the actual
on-time for the device at 50mA is (100%-12.5%) or 87.5%
of the time, or 87.5% duty cycle. Therefore, P D must be mul -
tiplied by the duty cycle to obtain the actual average power
dissipation at 50mA.
June 2009
10
M0371-061809
相关PDF资料 |
PDF描述 |
|---|---|
| VE-JW1-EZ-B1 | CONVERTER MOD DC/DC 12V 25W |
| BA033CC0T | IC REG LDO 3.3V 1A TO220FP |
| VI-JWZ-EZ-B1 | CONVERTER MOD DC/DC 2V 10W |
| VI-B54-EU-F3 | CONVERTER MOD DC/DC 48V 200W |
| VI-JWY-EZ-B1 | CONVERTER MOD DC/DC 3.3V 16.5W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5219YMM TR | 功能描述:低压差稳压器 - LDO 500mA Peak 1% Low Noise LDO(Lead Free) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC5219YMT | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:500mA-Peak Output LDO Regulator |
| MIC5219YMT TR | 功能描述:低压差稳压器 - LDO 500mA Peak Output, Adjustable Vout LDO in a 6-Pin 2x2 Thin MLF RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC5219YMT-TR | 功能描述:Linear Voltage Regulator IC Positive Adjustable 1 Output Adjustable 500mA 6-TMLF? (2x2) 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:有效 稳压器拓扑:正，可调式 电压 - 输出:可调 电流 - 输出:500mA 电压 - 跌落（典型值）:0.35V @ 500mA 稳压器数:1 电压 - 输入:2.5 V ~ 12 V 电流 - 限制（最小值）:- 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-UDFN 裸露焊盘，6-TMLF? 供应商器件封装:6-TMLF?（2x2） 标准包装:1 |
| MIC5225 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Ultra-Low Quiescent Current 150mA μCap Low Dropout Regulator |
发布紧急采购，3分钟左右您将得到回复。