- 您现在的位置：买卖IC网 > PDF目录13251 > MIC5247-1.8YM5 TR (Micrel Inc)IC REG LDO 1.8V .15A SOT23-5 PDF资料下载
参数资料
| 型号： | MIC5247-1.8YM5 TR |
| 厂商： | Micrel Inc |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.8V .15A SOT23-5 |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.8V |
| 输入电压： | 2.7 V ~ 6 V |
| 电压 - 压降（标准）： | 0.15V @ 150mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA |
| 电流 - 限制（最小）： | 160mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 标准包装 |
| 产品目录页面： | 1099 (CN2011-ZH PDF) |
| 其它名称： | 576-1288-6 |
P D ( max ) = ? J
? T ( max ) ? T A ?
θ JA
?
?
P D ( IN ? V OUT ) × I OUT + V IN × I GND
? 125 ° C ? 25 ° C ?
P D ( max ) = ? ?
1μF
MIC5247
Applications Information
Enable/Shutdown
The MIC5247 comes with an active-high enable pin that can
disable the regulator. Forcing the enable pin low disables the
regulator and sends it into a “zero” off-mode-current state.
In this state, current consumed by the regulator goes nearly
to zero. Forcing the enable pin high enables the output volt-
age. This part is CMOS and the enable pin cannot be left
?oating; a ?oating enable pin may cause an indeterminate
state on the output.
Input Capacitor
An input capacitor is not required for stability. A 1 μ F input
capacitor is recommended when the bulk AC supply capaci-
tance is more than 10 inches away from the device, or when
the supply is a battery.
Output Capacitor
The MIC5247 requires an output capacitor for stability. The
design requires 1 μ F or greater on the output to maintain stabil-
ity. The capacitor can be a low-ESR ceramic chip capacitor.
The MIC5247 has been designed to work speci?cally with
low-cost, small chip capacitors. Tantalum capacitors can also
be used for improved capacitance over temperature. The
value of the capacitor can be increased without bound.
Bypass Capacitor
A capacitor can be placed from the noise bypass pin to ground
to reduce output voltage noise. The capacitor bypasses the
internal reference. A 0.01 μ F capacitor is recommended for
applications that require low-noise outputs.
The bypass capacitor can be increased without bound, further
reducing noise and improving PSRR. Turn-on time remains
constant with respect to bypass capacitance. Refer to the
“Typical Characteristics” section for a graph of turn-on time
vs. bypass capacitor.
Transient Response
The MIC5247 implements a unique output stage to dramati-
cally improve transient response recovery time. The output is
a totem-pole con?guration with a P-Channel MOSFET pass
device and an N-Channel MOSFET clamp. The N-Channel
clamp is a signi?cantly smaller device that prevents the output
voltage from overshooting when a heavy load is removed.
This feature helps to speed up the transient response by
signi?cantly decreasing transient response recovery time
during the transition from heavy load (100mA) to light load
(85 μ A).
Active Shutdown
The MIC5247 also features an active shutdown clamp, which
is an N-Channel MOSFET that turns on when the device is
disabled. This allows the output capacitor and load to dis-
charge, de-energizing the load.
Thermal Considerations
The MIC5247 is designed to provide 150mA of continuous
current in a very small package. Maximum power dissipation
can be calculated based on the output current and the voltage
drop across the part. To determine the maximum power dis-
sipation of the package, use the junction-to-ambient thermal
Micrel, Inc.
resistance of the device and the following basic equation:
?
T J (max) is the maximum junction temperature of the die,
125°C, and T A is the ambient operating temperature. θ JA is
layout dependent; Table 1 shows examples of junction-to-
ambient thermal resistance for the MIC5247.
Package θ JA Recommended θ JA 1” Square θ JC
Minimum Footprint Copper Clad
SOT-23-5 (M5) 235°C/W 185°C/W 145°C/W
Table 1. SOT-23-5 Thermal Resistance
The actual power dissipation of the regulator circuit can be
determined using the equation:
= V
Substituting P D (max) for P D and solving for the operating
conditions that are critical to the application will give the
maximum operating conditions for the regulator circuit. For
example, when operating the MIC5247-2.4BM5 at room
temperature with a minimum footprint layout, the maximum
input voltage for a set output current can be determined as
follows:
? 235 ° C /W ?
P D ( max ) = 425mW
The junction-to-ambient thermal resistance for the minimum
footprint is 235°C/W, from Table 1. The maximum power dis-
sipation must not be exceeded for proper operation. Using
the output voltage of 2.4V and an output current of 150mA,
the maximum input voltage can be determined. Because this
device is CMOS and the ground current is typically 100 μ A over
the load range, the power dissipation contributed by the ground
current is < 1% and can be ignored for this calculation.
425mW = (V IN – 2.4V) 150mA
425mW = V IN × 150mA – 360mW
785mW = V IN × 150mA
V IN (max) = 5.2V
Therefore, a 2.4V application at 150mA of output current
can accept a maximum input voltage of 5.2V in a SOT-23-5
package. For a full discussion of heat sinking and thermal
effects on voltage regulators, refer to the “Regulator Ther-
mals” section of Micrel’s Designing with Low-Dropout Voltage
Regulators handbook.
Fixed Regulator Applications
1
V IN MIC5247-x.xBM5 V OU T
2
3 4
0.01μF
Figure 1. Ultra-Low-Noise Fixed Voltage Application
M9999-022406
8
February 2006
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1644EAE | IC REG BUCK SYNC ADJ 2A 16SSOP |
| TC1279-15ENBTR | IC RESET MONITOR 4.125V SOT23B-3 |
| GSM31DTMT | CONN EDGECARD 62POS R/A .156 SLD |
| RMC18DRYI-S734 | CONN EDGECARD 36POS DIP .100 SLD |
| GSA31DRMI | CONN EDGECARD 62POS .125 SQ WW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5247-2.0BD5 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:150mA Low-Voltage μCap Linear Regulator |
| MIC5247-2.0BD5 TR | 功能描述:IC REG LDO 2V .15A TSOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:500 系列:- 稳压器拓扑结构:正，固定式 输出电压:12V 输入电压:14.5 V ~ 35 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:500mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:TO-205AD，TO-39-3 金属罐 供应商设备封装:TO-39 包装:散装 其它名称:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
| MIC5247-2.0BD5TR | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| MIC5247-2.0BM5 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:150mA Low-Voltage μCap Linear Regulator |
| MIC5247-2.0BM5 TR | 功能描述:IC REG LDO 2V .15A SOT-23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:500 系列:- 稳压器拓扑结构:正，固定式 输出电压:12V 输入电压:14.5 V ~ 35 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:500mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:TO-205AD，TO-39-3 金属罐 供应商设备封装:TO-39 包装:散装 其它名称:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
发布紧急采购，3分钟左右您将得到回复。