- 您现在的位置：买卖IC网 > PDF目录19575 > MIC5265-3.1YD5 (Micrel Inc)IC REG LDO 3.1V .15A TSOT23-5 PDF资料下载
参数资料
| 型号： | MIC5265-3.1YD5 |
| 厂商： | Micrel Inc |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3.1V .15A TSOT23-5 |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3.1V |
| 输入电压： | 最高 5.5V |
| 电压 - 压降（标准）： | 0.21V @ 150mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 150mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 散装 |
Micrel, Inc.
Applications Information
Enable/Shutdown
The MIC5265 comes with an active-high enable pin that
allows the regulator in each output to be disabled.
Forcing the enable pin low disables the regulator and
sends it into a “zero” off-mode current state. In this state,
current consumed by the regulator goes nearly to zero.
Forcing the enable pin high enables the output voltage.
This part is CMOS and the enable pin cannot be left
floating; a floating enable pin may cause an
indeterminate state on the output.
Input Capacitor
The MIC5265 is a high performance, high bandwidth
device. Therefore, it requires well-bypassed input
supplies for optimal performance. A 1μF capacitor is
required from the input to ground to provide stability.
Low-ESR ceramic capacitors provide optimal
performance at a minimum of space. Additional high-
frequency capacitors, such as small valued NPO
dielectric type capacitors, help filter out high-frequency
noise and are good practice in any RF-based circuit.
Output Capacitor
The MIC5265 requires an output capacitor for stability.
The design requires 1μF or greater on each output to
maintain stability. The design is optimized for use with
low-ESR ceramic chip capacitors. High ESR capacitors
may cause high frequency oscillation. The maximum
recommended ESR is 300m ? . The output capacitor can
be increased, but performance has been optimized for a
1μF ceramic output capacitor and does not improve
significantly with larger capacitance.
X7R/X5R dielectric-type ceramic capacitors are
recommended because of their temperature
performance. X7Rtype capacitors change capacitance
MIC5265
large capacitor on the bypass pin without significantly
slowing turn-on time.
Active Shutdown
The MIC5265 also features an active shutdown clamp,
which is an N-channel MOSFET that turns on when the
device is disabled. This allows the output capacitor and
load to discharge, de-energizing the load.
No-Load Stability
The MIC5265 will remain stable and in regulation with no
load unlike many other voltage regulators. This is
especially important in CMOS RAM keep-alive
applications.
Thermal Considerations
The MIC5265 is designed to provide 150mA of
continuous current per output in a very small package.
Maximum ambient operating temperature can be
calculated based on the output current and the voltage
drop across the part. Given that the input voltage is
5.0V, the output voltage is 2.8V, and the output current
is 100mA.
The actual power dissipation of the regulator circuit can
be determined using the equation:
PD = (VIN – VOUT) IOUT + VIN IGND
Because this device is CMOS and the ground current is
typically <100μA over the load range, the power
dissipation contributed by the ground current is < 1%
and can be ignored for this calculation.
PD = (5.0V – 2.8V) x 150mA
PD = 0.33W
To determine the maximum ambient operating
temperature of the package, use the junction-to-ambient
thermal resistance of the device and the following basic
equation:
P D (max) = ? ?
?
?
by 15% over their operating temperature range and are
the most stable type of ceramic capacitors. Z5U and
Y5V dielectric capacitors change value by as much as
? T J (max) ? T A
? θ JA
?
?
50% and 60%, respectively, over their operating
temperature ranges. To use a ceramic chip capacitor
with Y5V dielectric, the value must be much higher than
an X7R ceramic capacitor to ensure the same minimum
capacitance over the equivalent operating temperature
range.
Bypass Capacitor
A capacitor can be placed from the noise bypass pin to
ground to reduce output voltage noise. The capacitor
bypasses the internal reference. A 0.01μF capacitor is
recommended for applications that require low-noise
outputs. The bypass capacitor can be increased, further
reducing noise and improving PSRR. Turn-on time
increases slightly with respect to bypass capacitance. A
unique quick-start circuit allows the MIC5265 to drive a
TJ(max) = 125°C, the max. junction temperature of the
die θ JA thermal resistance = 235°C/W
February 2007
9
M9999-022307
相关PDF资料 |
PDF描述 |
|---|---|
| VI-271-CY-F2 | CONVERTER MOD DC/DC 12V 50W |
| M5-512/256-6SAC | IC CPLD ISP 512MC 256IO 352SBGA |
| HBC65DRTI-S93 | CONN EDGECARD 130PS DIP .100 SLD |
| MIC5265-3.0YD5 | IC REG LDO 3V .15A TSOT23-5 |
| MIC5265-2.9YD5 | IC REG LDO 2.9V .15A TSOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5266-2.8YMT TR | 制造商:Micrel Inc 功能描述:The Micrel MIC5266-2.8YMT TR is a Low Dropout Voltage Regulator. |
| MIC5268-1.2BM5 | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: 制造商:Micrel Inc 功能描述: |
| MIC5268-1.2BM5 TR | 功能描述:IC REG LDO 1.2V .15A SOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:500 系列:- 稳压器拓扑结构:正，固定式 输出电压:12V 输入电压:14.5 V ~ 35 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:500mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:TO-205AD，TO-39-3 金属罐 供应商设备封装:TO-39 包装:散装 其它名称:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
| MIC5268-1.2BM5TR | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| MIC5268-1.2BM5TX | 功能描述:IC REG LDO 1.2V .15A SOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:500 系列:- 稳压器拓扑结构:正，固定式 输出电压:12V 输入电压:14.5 V ~ 35 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:500mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:TO-205AD，TO-39-3 金属罐 供应商设备封装:TO-39 包装:散装 其它名称:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
发布紧急采购，3分钟左右您将得到回复。