参数资料
| 型号： | MIC5307-3.0YD5 TR |
| 厂商： | Micrel Inc |
| 文件页数： | 7/9页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3V .3A TSOT23-5 |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3V |
| 输入电压： | 最高 5.5V |
| 电压 - 压降（标准）： | 0.12V @ 300mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 300mA |
| 电流 - 限制（最小）： | 350mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 标准包装 |
| 产品目录页面： | 1101 (CN2011-ZH PDF) |
| 其它名称： | 576-2855-6 |
Micrel, Inc.
Application Information
Input Capacitance
A 1 μ F capacitor should be placed from IN to GND if
there is more than 10 inches of wire between the input
and the ac filter capacitor or if a battery is used as the
input.
Output Capacitance
The MIC5307 requires an output capacitor of 2.2μF or
greater to maintain stability. The design is optimized for
use with low-ESR ceramic chip capacitors. High ESR
capacitors may cause high frequency oscillation. The
output capacitor can be increased, but performance has
been optimized for a 2.2μF ceramic output capacitor and
does not improve significantly with larger capacitance.
X7R/X5R dielectric-type ceramic capacitors are
recommended because of their temperature
MIC5307
Because this device is CMOS and the ground current is
typically < 50 μ A over the load range, the power dissipa-
tion contributed by the ground current is < 1% and can
be ignored for this calculation.
P D = (3.8V – 2.8V) ? 300mA
P D = 0.3W
To determine the maximum ambient operating tempera-
ture of the package, use the junction-to-ambient thermal
resistance of the device and the following basic
equation:
T J (max) – T A
P D (max) =
JA
T J (max) = 125 ° C, the maximum junction temperature of
the die θ JA thermal resistance = 235 ° C/W
Table 1 shows junction-to-ambient thermal resistance for
the MIC5307 in the TSOT23-5 package.
performance. X7R-type capacitors change capacitance
by 15% over their operating temperature range and are
the most stable type of ceramic capacitors. Z5U and
Y5V dielectric capacitors change value by as much as
50% and 60%, respectively, over their operating
Package
TSOT23-5
θ JA Recommended
Minimum Footprint
235 ° C/W
temperature ranges. To use a ceramic chip capacitor
with Y5V dielectric, the value must be much higher than
an X7R ceramic capacitor to ensure the same minimum
capacitance over the equivalent operating temperature
range.
Enable
Forcing EN (enable/shutdown) high (>1V) enables the
regulator. EN is compatible with CMOS logic gates. If the
enable/shutdown feature is not required, connect EN
(pin 3) to IN (supply input, pin 1).
Current Limit
There is overcurrent protection circuitry built into the
MIC5307. Even with the output grounded, current will be
limited to approximately 500mA. Further protection is
provided by thermal shutdown.
Thermal Considerations
The MIC5307 is designed to provide 300mA of
continuous current in a very small package. Maximum
ambient operating temperature can be calculated based
on the output current and the voltage drop across the
part. Given that the input voltage is 3.8V, the output
voltage is 2.8V and the output current equals 300mA.
The actual power dissipation of the regulator circuit can
be determined using the equation:
P D = (V IN – V OUT ) I OUT + V IN I GND
Table 1. TSOT23-5 Thermal Resistance
Substituting P D for P D (max) and solving for the ambient
operating temperature will give the maximum operating
conditions for the regulator circuit. The junction-to-
ambient thermal resistance for the minimum footprint is
235 ° C/W, from Table 1. The maximum power dissipation
must not be exceeded for proper operation.
For example, when operating the MIC5307-2.8 at an
input voltage of 3.8V and 300mA load with a minimum
footprint layout, the maximum ambient operating
temperature T A can be determined as follows:
0.3W = (125°C - T A ) / 235C°/W
T A = 54.5°C
Therefore, a 2.8V application at 300mA of output current
can accept an ambient operating temperature of 89.8 ° C
in a TSOT23-5 package. For a full discussion of heat
sinking and thermal effects on voltage regulators, refer
to the “Regulator Thermals” section of Micrel’s Designing
with Low-Dropout Voltage Regulators handbook. This
information can be found on Micrel's website at:
http://www.micrel.com/_PDF/other/LDOBk_ds.pdf
August 2007
7
M9999-082407-B
相关PDF资料 |
PDF描述 |
|---|---|
| MIC5308-1.2YD6 TR | IC REG LDO 1.2V .15A TSOT23-6 |
| MIC5309-1.2YMT TR | IC REG LDO 1.2V .3A 6-TMLF |
| MIC5310-OFYML TR | IC REG LDO 2.9V/1.5V .15A 8-MLF |
| MIC5311-NLYML TR | IC REG LDO 2.85V/2.7V .3A 10-MLF |
| MIC5313-F5YMT TR | IC REG LDO 1.5V/1.3V .3A 10-TMLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5308-1.0YMT | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
| MIC5308-1.2YD6 | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: |
| MIC5308-1.2YD6 TR | 功能描述:低压差稳压器 - LDO Low Vin/Vout, Low Iq 150mA ULDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC5308-1.2YD6-TR | 功能描述:Linear Voltage Regulator IC Positive Fixed 1 Output 1.2V 150mA TSOT-23-6 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 稳压器拓扑:正，固定式 电压 - 输出:1.2V 电流 - 输出:150mA 电压 - 跌落（典型值）:0.045V @ 150mA 稳压器数:1 电压 - 输入:1.6 V ~ 5.5 V 电流 - 限制（最小值）:180mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 细型，TSOT-23-6 供应商器件封装:TSOT-23-6 标准包装:1 |
| MIC5308-1.2YMT TR | 功能描述:低压差稳压器 - LDO Low Vin/Vout, Low Iq 150mA ULDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。