参数资料
| 型号： | MIC5318YMT TR |
| 厂商： | Micrel Inc |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ .3A 6-TMLF |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 1.25 V ~ 5.5 V |
| 输入电压： | 2.3 V ~ 6 V |
| 电压 - 压降（标准）： | 0.11V @ 300mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 300mA |
| 电流 - 限制（最小）： | 340mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-UFDFN 裸露焊盘，6-TMLF? |
| 供应商设备封装： | 6-TMLF?（1.6x1.6） |
| 包装： | 标准包装 |
| 产品目录页面： | 1103 (CN2011-ZH PDF) |
| 其它名称： | 576-2862-6 |
Micrel, Inc.
Application Information
Enable/Shutdown
The MIC5318 comes with an active-high enable pin
that allows the regulator to be disabled. Forcing the
enable pin low disables the regulator and sends it into
a “zero” off-mode-current state. In this state, current
consumed by the regulator goes nearly to zero.
Forcing the enable pin high enables the output
voltage. The active-high enable pin uses CMOS
technology and the enable pin cannot be left floating;
a floating enable pin may cause an indeterminate
state on the output.
Input Capacitor
The MIC5318 is a high-performance, high bandwidth
device. Therefore, it requires a well-bypassed input
supply for optimal performance. A 1μF capacitor
is required from the input to ground to provide
stability. Low-ESR ceramic capacitors provide optimal
performance at a minimum of space. Additional high-
frequency capacitors, such as small-valued NPO
dielectric-type capacitors, help filter out high-
frequency noise and are good practice in any RF-
based circuit.
Output Capacitor
The MIC5318 requires an output capacitor of 1μF or
greater to maintain stability. The design is optimized
MIC5318
Bypass Capacitor
A capacitor can be placed from the noise bypass pin
to ground to reduce output voltage noise. The
capacitor bypasses the internal reference. A 0.1 μ F
capacitor is recommended for applications that require
low-noise outputs. The bypass capacitor can be
increased, further reducing noise and improving
PSRR. Turn-on time increases slightly with respect to
bypass capacitance. A unique, quick-start circuit
allows the MIC5318 to drive a large capacitor on the
bypass pin without significantly slowing turn-on time.
Refer to the Typical Characteristics subsection for
performance with different bypass capacitors.
No-Load Stability
Unlike many other voltage regulators, the MIC5318
will remain stable and in regulation with no load. This
is especially crucial for CMOS RAM keep-alive
applications.
Adjustable Regulator Application
Adjustable regulators use the ratio of two resistors to
multiply the reference voltage to produce the desired
output voltage. The MIC5318 can be adjusted from
1.25V to 5.5V by using two external resistors (Figure
1). The resistors set the output voltage based on the
following equation:
V OUT = V REF ? 1 +
?
for use with low-ESR ceramic chip capacitors. High
ESR capacitors may cause high frequency oscillation.
The output capacitor can be increased, but
performance has been optimized for a 1μF ceramic
output capacitor and does not improve significantly
with larger capacitance.
X7R/X5R dielectric-type ceramic capacitors are
?
?
VREF = 1.25V
R1 ?
R2 ?
recommended because of their temperature perform-
ance. X7R-type capacitors change capacitance by
15% over their operating temperature range and are
the most stable type of ceramic capacitors. Z5U and
V IN
MIC5318YMT
VIN VOUT
R1
V OUT
Y5V dielectric capacitors change value by as much as
50% and 60%, respectively, over their operating
temperature ranges. To use a ceramic chip capacitor
1μF
EN
ADJ
GND
R2
1μF
with Y5V dielectric, the value must be much higher
than an X7R ceramic capacitor to ensure the same
minimum capacitance over the equivalent operating
temperature range.
Figure 1. Adjustable Voltage Output
September 2010
8
M9999-092810-B
相关PDF资料 |
PDF描述 |
|---|---|
| MIC5319-1.3HYD5 TR | IC REG LDO 1.375V .5A TSOT23-5 |
| MIC5320-PPYML TR | IC REG LDO 3V .15A 6-MLF |
| MIC5321-LLYMT TR | IC REG LDO 2.7V .15A 6-TMLF |
| MIC5322-PPYMT TR | IC REG LDO 3V .15A 6TMLF |
| MIC5325-1.8YMT TR | IC REG LDO 1.8V .4A 6-TMLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5319-1.3HYD5 TR | 功能描述:低压差稳压器 - LDO 500mA Cap Ultra-Low Dropout, High PSRR LDO Regulator in TSOT (Lead Free) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC5319-1.3HYD5-TR | 功能描述:Linear Voltage Regulator IC Positive Fixed 1 Output 1.375V 500mA TSOT-23-5 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 稳压器拓扑:正，固定式 电压 - 输出:1.375V 电流 - 输出:500mA 电压 - 跌落（典型值）:- 稳压器数:1 电压 - 输入:2.5 V ~ 5.5 V 电流 - 限制（最小值）:600mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 供应商器件封装:TSOT-23-5 标准包装:1 |
| MIC5319-1.3HYML TR | 功能描述:低压差稳压器 - LDO 500mA Cap Ultra-Low Dropout, High PSRR LDO Regulator in 2mm x 2mm MLF (Lead Free) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC5319-1.5BD5 | 功能描述:IC REG LDO 1.5V .5A TSOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:500 系列:- 稳压器拓扑结构:正，固定式 输出电压:12V 输入电压:14.5 V ~ 35 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:500mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:TO-205AD，TO-39-3 金属罐 供应商设备封装:TO-39 包装:散装 其它名称:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
| MIC5319-1.5BD5 TR | 功能描述:IC REG LDO 1.5V .5A TSOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:500 系列:- 稳压器拓扑结构:正，固定式 输出电压:12V 输入电压:14.5 V ~ 35 V 电压 - 压降（标准）:- 稳压器数量:1 电流 - 输出:500mA 电流 - 限制（最小）:- 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:TO-205AD，TO-39-3 金属罐 供应商设备封装:TO-39 包装:散装 其它名称:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
发布紧急采购，3分钟左右您将得到回复。