参数资料
| 型号： | MIC5322-PMYMT TR |
| 厂商： | Micrel Inc |
| 文件页数： | 7/9页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 3V/2.8V .15A 6TMLF |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 3V，2.8V |
| 输入电压： | 2.3 V ~ 5.5 V |
| 电压 - 压降（标准）： | 0.035V @ 150mA |
| 稳压器数量： | 2 |
| 电流 - 输出： | 150mA |
| 电流 - 限制（最小）： | 300mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-UFDFN 裸露焊盘，6-TMLF? |
| 供应商设备封装： | 6-TMLF?（1.6x1.6） |
| 包装： | 标准包装 |
| 产品目录页面： | 1104 (CN2011-ZH PDF) |
| 其它名称： | 576-3028-6 |
?
Micrel, Inc.
Applications Information
/Enable/Shutdown
The MIC5322 comes with a single active-low enable
pin that allows both regulators to be disabled
simultaneously. Forcing the enable pin high disables
the regulators and sends it into a “zero” off-mode-
current state. In this state, current consumed by the
regulator goes nearly to zero. Forcing the enable pin
low enables the output voltages. The active-low
enable pin cannot be left floating since a floating
enable pin may cause an indeterminate state on the
output.
Input Capacitor
The MIC5322 is a high-performance, high bandwidth
device. Therefore optimal performance can be
achieved by providing a well-bypassed input supply. A
1μF capacitor is required from the input-to-ground to
provide stability. Low-ESR ceramic capacitors provide
optimal performance at a minimum of space.
Additional high-frequency capacitors, such as small-
valued NPO dielectric-type capacitors, help filter out
high-frequency noise and are good practice in any
RF-based circuit.
Output Capacitor
The MIC5322 requires an output capacitor of 1μF or
greater to maintain stability. The design is optimized,
for use, with low-ESR ceramic chip capacitors. High
ESR capacitors may cause high frequency oscillation.
The output capacitor can be increased, but
performance has been optimized for a 1μF ceramic
output capacitor and does not improve significantly
with larger capacitance.
X7R/X5R dielectric-type ceramic capacitors are
recommended because of their temperature stable
performance. X7R-type capacitors change
capacitance by 15% over their operating temperature
range and are the most stable type of ceramic
capacitors. Z5U and Y5V dielectric capacitors change
value by as much as 50% and 60%, respectively, over
their operating temperature ranges. To use a ceramic
chip capacitor with Y5V dielectric, the value must be
much higher than an X7R ceramic capacitor to ensure
the same minimum capacitance over the equivalent
operating temperature range.
MIC5322
Bypass Capacitor
A capacitor can be placed from the noise bypass pin-
to-ground to reduce output voltage noise. The
capacitor bypasses the internal reference. A 0.1μF
capacitor is recommended for applications that require
low-noise outputs. The bypass capacitor can be
increased, further reducing noise and improving
PSRR. Turn-on time increases slightly with respect to
bypass capacitance. A unique, quick-start circuit
allows the MIC5322 to drive a large capacitor on the
bypass pin without significantly slowing turn-on time.
Refer to the Typical Characteristics section of this
datasheet for performance with different bypass
capacitors.
No-Load Stability
Unlike many other voltage regulators, the MIC5322
will remain stable and in regulation with no load. This
is especially important in CMOS RAM keep-alive
applications.
Thermal Considerations
The MIC5322 is designed to provide 150mA of
continuous current for both outputs in a very small
package. Maximum ambient operating temperature
can be calculated based on the output current and the
voltage drop across the part. As an example: Given
that the input voltage is 3.3V, the output voltage is
2.8V for V OUT1 , 1.5V for V OUT2 and the output current at
150mA. The actual power dissipation of the regulator
circuit can be determined using the equation:
P D = (V IN – V OUT1 ) I OUT1 + (V IN – V OUT2 ) I OUT2 + V IN I GND
Because this device is CMOS and the ground current
is typically <150μA over the load range, the power
dissipation contributed by the ground current is < 1%
and can be ignored for this calculation.
P D = (3.3V – 2.8V) × 150mA + (3.3V -1.5) × 150mA
PD = 0.345W
To determine the maximum ambient operating
temperature of the package, use the junction-to-
ambient thermal resistance of the device and the
following basic equation:
? T J(MAX) - T A
P D(MAX) =
JA
T J(max) = 125°C, the maximum junction temperature of
the die θ JA thermal resistance = 100°C/W.
The table below shows junction-to-ambient thermal
resistance for the MIC5322 in the Thin MLF ? package.
May 2008
7
M9999-051508-B
相关PDF资料 |
PDF描述 |
|---|---|
| MIC5322-NNYMT TR | IC REG LDO 2.85V .15A 6TMLF |
| HSC44DRYS | CONN EDGECARD 88POS DIP .100 SLD |
| EMC12DTEF | CONN EDGECARD 24POS .100 EYELET |
| GBB90DHBN | CONN EDGECARD 180PS R/A .050 SLD |
| LT3070EUFD#TRPBF | IC REG LDO ADJ 5A 28QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5322-PNYMT TR | 功能描述:低压差稳压器 - LDO Dual 150mA LDO Thin MLF Enable, Bypass and Shutdown (Lead Free) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC5322-PNYMT-TR | 功能描述:Linear Voltage Regulator IC Positive Fixed 2 Output 3V, 2.85V 150mA 6-TMLF? (1.6x1.6) 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 稳压器拓扑:正，固定式 电压 - 输出:3V，2.85V 电流 - 输出:150mA 电压 - 跌落（典型值）:0.035V @ 150mA 稳压器数:2 电压 - 输入:2.3 V ~ 5.5 V 电流 - 限制（最小值）:300mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-UFDFN 裸露焊盘，6-TMLF? 供应商器件封装:6-TMLF?（1.6x1.6） 标准包装:1 |
| MIC5322-PPYMT TR | 功能描述:低压差稳压器 - LDO Dual 150mA LDO Thin MLF Enable, Bypass and Shutdown (Lead Free) RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC5322-PPYMT-TR | 功能描述:Linear Voltage Regulator IC Positive Fixed 2 Output 3V 150mA 6-TMLF? (1.6x1.6) 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 稳压器拓扑:正，固定式 电压 - 输出:3V 电流 - 输出:150mA 电压 - 跌落（典型值）:0.035V @ 150mA 稳压器数:2 电压 - 输入:2.3 V ~ 5.5 V 电流 - 限制（最小值）:300mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-UFDFN 裸露焊盘，6-TMLF? 供应商器件封装:6-TMLF?（1.6x1.6） 标准包装:1 |
| MIC5323-1.8YD5 TR | 功能描述:低压差稳压器 - LDO 300mA uCap ULDO High PSRR Low Noise Regulator RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。