参数资料
| 型号： | MIC5332-J4YMT TR |
| 厂商： | Micrel Inc |
| 文件页数： | 9/13页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 2.5V/1.2V .3A 8TMLF |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 2.5V，1.2V |
| 输入电压： | 2.3 V ~ 5.5 V |
| 电压 - 压降（标准）： | 0.12V @ 300mA |
| 稳压器数量： | 2 |
| 电流 - 输出： | 300mA |
| 电流 - 限制（最小）： | 350mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-VFDFN 裸露焊盘，8-MLF? |
| 供应商设备封装： | 8-MLF?（2x2） |
| 包装： | 标准包装 |
| 产品目录页面： | 1104 (CN2011-ZH PDF) |
| 其它名称： | 576-3158-6 |
Micrel, Inc.
Application Information
MIC5332 is a dual, 300mA LDO, with an integrated
power-on reset (POR) for the second regulator. The
MIC5332 regulator is fully protected from damage due to
fault conditions, offering linear current limiting and
thermal shutdown.
Input Capacitor
The MIC5332 is a high-performance, high-bandwidth
device. Therefore, it requires a well-bypassed input
supply for optimal performance. A 1μF capacitor is
required from the input to ground to provide stability.
Low-ESR ceramic capacitors provide optimal
performance at a minimum of space. Additional high-
frequency capacitors, such as small-valued NPO
dielectric-type capacitors, help filter out high-frequency
noise and are good practice in any RF-based circuit.
X5R or X7R dielectrics are recommended for the input
capacitor. Y5V dielectrics lose most of their capacitance
over temperature and are therefore, not recommended.
Output Capacitor
The MIC5332 requires an output capacitor of 1μF or
greater to maintain stability. The design is optimized for
use with low-ESR ceramic chip capacitors. High-ESR
capacitors may cause high frequency oscillation. The
output capacitor can be increased, but performance has
been optimized for a 1μF ceramic output capacitor and
does not improve significantly with larger capacitance.
X7R/X5R dielectric-type ceramic capacitors are
recommended because of their temperature
performance. X7R-type capacitors change capacitance
by 15% over their operating temperature range and are
the most stable type of ceramic capacitors. Z5U and
Y5V dielectric capacitors change value by as much as
50% and 60%, respectively, over their operating
temperature ranges. To use a ceramic chip capacitor
with Y5V dielectric, the value must be much higher than
an X7R ceramic capacitor to ensure the same minimum
capacitance over the equivalent operating temperature
range.
No-Load Stability
Unlike many other voltage regulators, the MIC5332 will
remain stable and in regulation with no load. This is
especially import in CMOS RAM keep-alive applications.
MIC5332
Enable/Shutdown
The MIC5332 comes with dual active-high enable pins
that allow each regulator to be disabled independently.
Forcing the enable pin low disables the regulator and
sends it into a “zero” off-mode-current state. In this state,
current consumed by the regulator goes nearly to zero.
Forcing the enable pin high enables the output voltage.
The active-high enable pin uses CMOS technology and
the enable pin cannot be left floating; a floating enable
pin may cause an indeterminate state on the output.
Power-On-Reset
The second regulator has a power-on-reset status pin
(POR2). This pin is an open drain output. When LDO2 is
enabled an active low POR2 indicates an undervoltage
condition on V OUT2 .
The POR2 status signal can be programmed for a delay
of 1sec/μF by placing a capacitor from the CSET2 pin to
ground. Zero delay is added by leaving the CSET2 pin
open circuit.
Thermal Considerations
The MIC5332 is designed to provide 300mA of
continuous current for both outputs in a very small
package. Maximum ambient operating temperature can
be calculated based upon the output current and the
voltage drop across the part. For example if the input
voltage is 3.6V, the output voltage is 3.0V for V OUT1 , 2.8V
for V OUT2 and the output current = 300mA. The actual
power dissipation of the regulator circuit can be
determined using the equation:
P D = (V IN – V OUT1 ) I OUT1 + (V IN – V OUT2 ) I OUT2 + V IN I GND
Because this device is CMOS and the ground current is
typically <100μA over the load range, the power
dissipation contributed by the ground current is < 1%
and can be ignored for this calculation:
P D = (3.6V – 3.0V) × 300mA + (3.6V -2.8) × 300mA
P D = 0.42W
September 2012
9
M9999-091212-B
相关PDF资料 |
PDF描述 |
|---|---|
| MIC5332-PMYMT TR | IC REG LDO 3V/2.8V .3A 8TMLF |
| ISL6334AIRZ-TR5368 | IC CTRLR PWM 4PHASE BUCK 40QFN |
| ISL6334IRZ-T | IC CTRLR PWM 4PHASE BUCK 40-QFN |
| RCA30DRSZ-S273 | CONN EDGECARD 60POS DIP .125 SLD |
| AMM15DRKH-S13 | CONN EDGECARD 30POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC5332-MMYMT TR | 功能描述:低压差稳压器 - LDO Dual 300mA micropower ULDO with POR RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC5332-MMYMT-TR | 功能描述:Linear Voltage Regulator IC Positive Fixed 2 Output 2.8V 300mA 8-MLF? (2x2) 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 稳压器拓扑:正，固定式 电压 - 输出:2.8V 电流 - 输出:300mA 电压 - 跌落（典型值）:0.12V @ 300mA 稳压器数:2 电压 - 输入:2.3 V ~ 5.5 V 电流 - 限制（最小值）:350mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 供应商器件封装:8-MLF?（2x2） 标准包装:1 |
| MIC5332-MNYMT TR | 功能描述:低压差稳压器 - LDO Dual 300mA micropower ULDO with POR RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MIC5332-MNYMT-TR | 功能描述:Linear Voltage Regulator IC Positive Fixed 2 Output 2.8V, 2.85V 300mA 8-MLF? (2x2) 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 稳压器拓扑:正，固定式 电压 - 输出:2.8V，2.85V 电流 - 输出:300mA 电压 - 跌落（典型值）:0.12V @ 300mA 稳压器数:2 电压 - 输入:2.3 V ~ 5.5 V 电流 - 限制（最小值）:350mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘，8-MLF? 供应商器件封装:8-MLF?（2x2） 标准包装:1 |
| MIC5332-NNYMT TR | 功能描述:低压差稳压器 - LDO Dual 300mA micropower ULDO with POR RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。